Fiat JTD engine


Multijet is a Fiat and General Motors joint venture, established in 1996, in manufacturing diesel engines with turbo and common rail direct injection technology. Most of the Fiat S.p.A., Fiat Professional, Groupe PSA, Alfa Romeo, Maserati, Lancia, Chrysler, Chevrolet, Daewoo Motors, Cadillac, Karsan, Temsa, Iveco, Jeep, Opel, Vauxhall Motors, RAM Trucks, Mitsubishi Fuso, Maruti Suzuki, Suzuki, Tata Motors and Saab Automobile branded vehicles are equipped with Multijet engines. Ownership of some Fiat Multijet designs is shared with General Motors as part of a settlement of the failed merger between the two auto conglomerates. The GM Powertrain Torino group in Turin, Italy, manages its interest in these engines. Some PSA [Peugeot Citroën] diesel engines are also rebadged JTD units, and vice versa. Fiat's common-rail diesel engine is also known as JTD, an initialism of UniJet Turbo Diesel.

Characteristics

The main improvement that distinguishes the Multijet from previous generations of common-rail diesel engines from Fiat [Chrysler Automobiles|FCA] is the combustion process of the fuel, which is split into multiple injections, thus allowing for a more complete, quieter combustion in the cylinder. Compared to the first-generation JTD engines, which only featured a smaller pilot and a larger main injection, Multijet is capable of up to five injections per combustion cycle which enables better, more efficient cold running, better performance especially in the lower rev-range, quieter operation, as well as even lower consumption and emissions. The time between injections has been reduced to 150 microseconds while the minimal injection quantity has been reduced from two to less than one microlitre. This enables even mid-sized sedans like the Alfa Romeo 156 and Lancia Lybra equipped with the 1.9L JTD to achieve fuel economy upwards of 45 mpgUS on country roads and highways while offering an equal amount of torque as the 3.0L 24V V6 engine.
A sophisticated electronic control unit controls the injection and changes the injection logic and number of injections based on a multitude of parameters, most importantly revolutions per minute of the engine, engine torque requested by the driver and the temperature of the coolant.
The injection pressure of the diesel fuel on the second-generation Multijet is limited to between bar on the 1.3 Multijet and bar on the 2.4 Multijet 20V.

Multijet II

In 2009, Fiat Powertrain introduced the third generation of this technology, called Multijet II. With its new and innovative injectors with a hydraulically balanced solenoid valve and even higher injection pressure of 2,000 bar it is capable of even more precise controlling of the injected diesel fuel, injecting it in a quicker and more flexible manner. It enables up to eight consecutive injections per combustion cycle and implemented Injection Rate Shaping technology, which provides two very close pilot injections making the fuel delivery more continuous and modulated. This results in an engine that is quiet and has a smoother operation, lower emissions, better fuel mileage and higher performance compared to the previous generation.

Automotive engines

0.9

A 3-cylinder variant, or Smartech Diesel, was introduced in 2011. Co-developed by GM Powertrain Torino and the GM Technical Center India for the Indian market the engine is rated at of power and of torque.
Applications:

1.2 JTDm/Multijet/CDTI/D/DDiS/HDi

A small version was introduced in February 2003 is produced in Bielsko-Biała, Poland, in Ranjangaon, Pune, India, by Fiat India Automobiles and Tata Motors joint venture plant since 2008, and by Maruti Suzuki in Gurgaon, Haryana, India since 2012. The Multijet 75 PS version was chosen in 2005 as the International Engine of the Year in the 1-litre to 1.4-litre category. There are five versions of this engine: a and a, a, a variable inlet geometry and a from the Multijet II generation, and a available on the Lancia Ypsilon. Newton metre torque in the,, and. At the time of the launch this was the smallest four-cylinder diesel engine available and it had a fuel consumption of in some applications. The engine is able to meet Euro IV emission standards without the use of a diesel particulate filter. In January 2008, Tata Motors introduced the new Indica Vista model, which features a new Quadrajet branded version of this engine. The second generation Ford Ka uses 1.2 Multijet named as Duratorq TDCi. In GM nomenclature, it is called Small Diesel Engine.
During 2009, Fiat launched a new generation badged Multijet II, with a new injection management system and able to meet Euro V emission standards. It is available with several power outputs, from, with fixed geometry turbocharger, to, with variable geometry turbocharger.
As of 2013, more than 5 million 1.2 MultiJet engines were produced. In January 2020, the production of the 1.2 Multijet ended in India in both the Maruti Suzuki plant and the Fiat-Tata JV, as the BS6 emission regulations came into effect in the country from 1 April 2020. Fiat-Tata built a total of 800,048 engines over 12 years.

Applications

FCA

1.6 JTDm/Multijet/CDTI/DDiS

In 2006 Fiat Powertrain announced a downsized version of the 1.9 16V Multijet, a new 1.6L 16V Multijet with two power levels of,, and to replace the still-used 1.9L 8-valve engine. The new 1.6 Multijet diesel with,, and.

Applications

FCA

1.9 JTD/JTDm/Multijet/Twin Turbo Multijet/CDTI/TiD/TTiD/DDiS

The most common JTD engine is the 1.9 L straight-4 found on various brands and models. The first car that used this engine was the Alfa Romeo 156 in 1997, making it the world's first common-rail diesel passenger car. In 1999, it was introduced in the Fiat Brava, Bravo and Marea range, as well as in the Fiat Punto JTD with a smaller, fixed-geometry turbocharger and. There were also,,, and versions available. The engine block weighs approximately, the cylinder head features an overhead camshaft with directly actuated valves. The Multijet second generation features an advanced common-rail system and is available with seven different power outputs. The 8-valve version has,, or and the 16-valve version has,,, or. Except for the 101 PS Multijet, all engines feature a variable-geometry turbocharger. Opel also uses a version of this engine. Their CDTI engine, manufactured in Pratola Serra, Italy and Kaiserslautern, Germany, is the product of the half-decade joint venture between GM and Fiat. It is used in the Vectra, Signum, Astra, Zafira, Cadillac BLS and Suzuki SX4 as well as some Saabs marked as TiD and TTiD.

Applications

FCA

Twin Turbo

Fiat Powertrain Technologies released information about a new two stage turbo version of this engine in summer 2007, which is available with two power levels, one producing and one, both with a maximum torque output of at 2000 rpm. The 180 PS version production started summer 2007. The engine weighs approximately. This engine will be sold both to Fiat Group Automobiles and other brands, but the version is reserved only to Fiat Group Automobiles.
Applications

2.0 JTDm/CDTI/TiD/TTiD/VCDi/Multijet II/DDiS

A new 2 litre Multijet diesel was introduced in third generation Lancia Delta in summer 2008. At its first version this engine produces. For 2009 the engine was fitted to Alfa Romeo 159 as variant. Fiat Sedici, Suzuki SX4 and the new Fiat Doblò generation use a variant of this engine. GM Powertrain separately developed their diesel engines based on 1.9 JTD, after end of the GM and Fiat partnership, and first was the version for Astra and Insignia, which was later upgraded to 165 PS for Astra, and less powerful version for Insignia with 110 PS and 130 PS. In 2011 GM Powertrain Europe developed a new derivative - the twin-turbocharger BiTurbo version, with, which is used in the Insignia and starting with 2013 in the Astra J. Internally the new engine is referred to as GM Ecotec Family B engine. The same engine was also available in the 2011 Saab 9–5 with 160 PS and 190 PS twin-turbo. In 2013 Opel introduced cleaner and more fuel efficient versions of the 2.0 CDTI engine and the ecoFLEX version, with 99 g/km of CO2 and 120 PS.

Applications

FCA

2.2 JTDm/Multijet II

The 2.2 Multijet II was introduced by Fiat Chrysler in mid-2015. These engines produce and with of torque at 2500 RPM in the Jeep Cherokee. It was developed to offer more torque in the low-rev range compared to the 2.0L Multijet. This engine further improves the existing 2.0 Multijet in various areas, such as a higher injection pressure with Injector Rate Shaping, an oil pump with variable displacement and counterbalance-shafts to reduce noises and vibrations. This engine meets Euro 6 emission norms without the use of diesel exhaust fluid injection. A 2.2 Multijet III was introduced by Stellantis on the Fiat Ducato in 2021 with 4 power outputs: 120, 140, 160, & 180 hp. It meets Euro 6d emissions standards.
A further development of this engine with a 2,143 cc displacement, and a die-cast Aluminium block, is used in the Alfa Romeo Giulia (952), Alfa Romeo Stelvio, and Jeep Wrangler (JL).
Announced in 2023, a new version of the 2.2 Multijet Evo four-cylinder engine entered production in 2024 and was Euro 7 approved in 2025. This engine produced in the Pratola Serra factory is mounted on the Fiat Ducato, Peugeot Landtrek, Fiat Titano, RAM Rampage, Fiat Toro, Jeep Compass and Jeep Commander. The South American version was Proconve L8 homologated.
From 2025, the 2.2 Multijet Evo engine will also be adopted by K0 commercial vehicles, replacing the previous 1.5 HDI and 2.0 HDI engines of PSA origin.

Applications

;2,143 cc aluminium block
;2,184 cc cast-iron block

2.4 JTD/JTDm/Multijet

The 2.4 L straight-5 version is based on the 2.4 5 cylinder TD engine as used in the Mk1 Fiat Marea and the Mk1 Lancia Kappa. The JTD version benefits from the solid build of the TD block, and an improved head/injection system. There are 2 versions of the 2.4 JTD, the 10-valve as used in the Fiat Marea 130 JTD and the earlier Alfa Romeo 156/Alfa Romeo 166/Lancia Lybra diesels where it was available as,, and later a Multijet 20-valve version as used in the later Alfa Romeo 156 as well as some Lancia vehicles. It was designed for transverse front-wheel drive use and was deemed too long and tall for widespread use in other GM Ecotec or Fiat products. A newer Multijet variant of this engine, capable for, is used in the Alfa Romeo 159, Alfa Romeo Brera and Fiat Croma. The latest version of this engine produces and at 1500 rpm, and is used in Alfa Romeo vehicles.

Applications

2.8

Evolution of VM Motori A 428 DOHC in the inline-4 engine with 1,800 bar common rail injection system and piezoelectric injectors

Applications

3.0

A double overhead camshaft V6 engine, featuring four valves-per-cylinder and common-rail direct fuel injection. A variant complying with the emission norms of the North America market is the 3.0 V6 Multijet II and marketed by Fiat Chrysler as the FPT Multijet II. The high-performance, single turbo version is Jeep.

A630 applications (Europe)

L630 applications (North America)

A630 HP applications (Europe)

Light commercial vehicle engines

1.5 Multijet II

The Multijet II engine is a 1.5 L inline-four found on various brands and models. Versions of this engine include the PSA DV5 in the third generation Fiat Doblò and third generation Fiat Scudo. Power outputs are, with maximum torque output of or at 2000 rpm. The PSA HDi engine variant is manufactured by Groupe PSA as a product of the joint venture with Stellantis.

Applications

Fiat

1.6 Multijet II

The 1.6 Multijet II was developed by PSA HDi engine and Ford Duratorq engine for heavy-duty applications and is available in three versions 90 Multijet these engines produce respectively.

Applications

2.0 JTD/Multijet

The 2.0 JTD/Multijet was developed by PSA HDi engine for heavy-duty applications and is available in three versions 90 JTD, 110 JTD, 120 MultiJet, 136 MultiJet, 150 MultiJet and 180 MultiJet these engines produce,,,, and respectively.

Applications

2.3 JTD/Multijet

The 2.3 Multijet was developed by Iveco for heavy-duty applications and is available in three versions 120 MultiJet, 130 MultiJet and 150 MultiJet, these engines produce, and respectively.

Applications

2.4 Multijet

The 2.4 Multijet was developed by Mitsubishi 4N15 for Mitsubishi L200 applications and is available in three versions these engines produce and respectively.

Applications

2.8 JTD/HDi

The 2.8 JTD made by Iveco was used in second generation Fiat Ducato, it produces or.

Applications

3.0 Multijet Power/HDi

The 160 MultiJet Power, introduced in 2007, saw displacement increased to 3.0 L. This engine produces or in Fiat-badged models. In Iveco Massif this engine is also available as version.

Applications