Ice core
An ice core is a core sample that is typically removed from an ice sheet or a high mountain glacier. Since the ice forms from the incremental buildup of annual layers of snow, lower layers are older than upper ones, and an ice core contains ice formed over a range of years. Cores are drilled with hand augers or powered drills; they can reach depths of over two miles, and contain ice up to 800,000 years old.
The physical properties of the ice and of material trapped in it can be used to reconstruct the climate over the age range of the core. The proportions of different oxygen and hydrogen isotopes provide information about ancient temperatures, and the air trapped in tiny bubbles can be analysed to determine the level of atmospheric gases such as carbon dioxide. Since heat flow in a large ice sheet is very slow, the borehole temperature is another indicator of temperature in the past. This data can be combined to find the climate model that best fits all the available data.
Impurities in ice cores may depend on location. Coastal areas are more likely to include material of marine origin, such as sea salt ions. Greenland ice cores contain layers of wind-blown dust that correlate with cold, dry periods in the past, when cold deserts were scoured by wind. Radioactive elements, either of natural origin or created by nuclear testing, can be used to date the layers of ice. Some volcanic events that were sufficiently powerful to send material around the globe have left a signature in many different cores that can be used to synchronise their time scales.
Ice cores have been studied since the early 20th century, and several cores were drilled as a result of the International Geophysical Year. Depths of over 400 m were reached, a record which was extended in the 1960s to 2164 m at Byrd Station in Antarctica. Soviet ice drilling projects in Antarctica include decades of work at Vostok Station, with the deepest core reaching 3769 m. Numerous other deep cores in the Antarctic have been completed over the years, including the West Antarctic Ice Sheet project, and cores managed by the British Antarctic Survey and the International Trans-Antarctic Scientific Expedition. In Greenland, a sequence of collaborative projects began in the 1970s with the Greenland Ice Sheet Project; there have been multiple follow-up projects, with the most recent, the East Greenland Ice-Core Project, originally expected to complete a deep core in east Greenland in 2020 but since postponed.
Structure of ice sheets and cores
An ice core is a vertical column through a glacier, sampling the layers that formed through an annual cycle of snowfall and melt. As snow accumulates, each layer presses on lower layers, making them denser until they turn into firn. Firn is not dense enough to prevent air from escaping; but at a density of about 830 kg/m3 it turns to ice, and the air within is sealed into bubbles that capture the composition of the atmosphere at the time the ice formed. The depth at which this occurs varies with location, but in Greenland and the Antarctic it ranges from 64 m to 115 m. Because the rate of snowfall varies from site to site, the age of the firn when it turns to ice varies a great deal. At Summit Camp in Greenland, the depth is 77 m and the ice is 230 years old; at Dome C in Antarctica the depth is 95 m and the age 2500 years. As further layers build up, the pressure increases, and at about 1500 m the crystal structure of the ice changes from hexagonal to cubic, allowing air molecules to move into the cubic crystals and form a clathrate. The bubbles disappear and the ice becomes more transparent.Two or three feet of snow may turn into less than a foot of ice. The weight above makes deeper layers of ice thin and flow outwards. Ice is lost at the edges of the glacier to icebergs, or to summer melting, and the overall shape of the glacier does not change much with time. The outward flow can distort the layers, so it is desirable to drill deep ice cores at places where there is very little flow. These can be located using maps of the flow lines.
Impurities in the ice provide information on the environment from when they were deposited. These include soot, ash, and other types of particle from forest fires and volcanoes; isotopes such as beryllium-10 created by cosmic rays;
micrometeorites; and pollen. The lowest layer of a glacier, called basal ice, is frequently formed of subglacial meltwater that has refrozen. It can be up to about 20 m thick, and though it has scientific value, it often does not retain stratigraphic information.
Cores are often drilled in areas such as Antarctica and central Greenland where the temperature is almost never warm enough to cause melting, but the summer sunlight can still alter the snow. In polar areas, the Sun is visible day and night during the local summer and invisible all winter. It can make some snow sublimate, leaving the top inch or so less dense. When the Sun approaches its lowest point in the sky, the temperature drops and hoar frost forms on the top layer. Buried under the snow of following years, the coarse-grained hoar frost compresses into lighter layers than the winter snow. As a result, alternating bands of lighter and darker ice can be seen in an ice core.
Coring
Ice cores are collected by cutting around a cylinder of ice in a way that enables it to be brought to the surface. Early cores were often collected with hand augers and they are still used for short holes. A design for ice core augers was patented in 1932 and they have changed little since. An auger is essentially a cylinder with helical metal ribs wrapped around the outside, at the lower end of which are cutting blades. Hand augers can be rotated by a T handle or a brace handle, and some can be attached to handheld electric drills to power the rotation. With the aid of a tripod for lowering and raising the auger, cores up to 50 m deep can be retrieved, but the practical limit is about 30 m for engine-powered augers, and less for hand augers. Below this depth, electromechanical or thermal drills are used.The cutting apparatus of a drill is on the bottom end of a drill barrel, the tube that surrounds the core as the drill cuts downward. The cuttings must be drawn up the hole and disposed of or they will reduce the cutting efficiency of the drill. They can be removed by compacting them into the walls of the hole or into the core, by air circulation, or by the use of a drilling fluid. Dry drilling is limited to about 400 m depth, since below that point a hole would close up as the ice deforms from the weight of the ice above.
Drilling fluids are chosen to balance the pressure so that the hole remains stable. The fluid must have a low kinematic viscosity to reduce tripping time. Since retrieval of each segment of core requires tripping, a slower speed of travel through the drilling fluid could add significant time to a project—a year or more for a deep hole. The fluid must contaminate the ice as little as possible; it must have low toxicity, for safety and to minimize the effect on the environment; it must be available at a reasonable cost; and it must be relatively easy to transport. Historically, there have been three main types of ice drilling fluids: two-component fluids based on kerosene-like products mixed with fluorocarbons to increase density; alcohol compounds, including aqueous ethylene glycol and ethanol solutions; and esters, including n-butyl acetate. Newer fluids have been proposed, including new ester-based fluids, low-molecular weight dimethyl siloxane oils, fatty-acid esters, and kerosene-based fluids mixed with foam-expansion agents.
Rotary drilling is the main method of drilling for minerals and it has also been used for ice drilling. It uses a string of drill pipe rotated from the top, and drilling fluid is pumped down through the pipe and back up around it. The cuttings are removed from the fluid at the top of the hole and the fluid is then pumped back down. This approach requires long trip times, since the entire drill string must be hoisted out of the hole, and each length of pipe must be separately disconnected, and then reconnected when the drill string is reinserted. Along with the logistical difficulties associated with bringing heavy equipment to ice sheets, this makes traditional rotary drills unattractive. In contrast, wireline drills allow the removal of the core barrel from the drill assembly while it is still at the bottom of the borehole. The core barrel is hoisted to the surface, and the core removed; the barrel is lowered again and reconnected to the drill assembly. Another alternative is flexible drill-stem rigs, in which the drill string is flexible enough to be coiled when at the surface. This eliminates the need to disconnect and reconnect the pipes during a trip. The need for a string of drillpipe that extends from the surface to the bottom of the borehole can be eliminated by suspending the entire downhole assembly on an armoured cable that conveys power to the downhole motor. These cable-suspended drills can be used for both shallow and deep holes; they require an anti-torque device, such as leaf-springs that press against the borehole, to prevent the drill assembly rotating around the drillhead as it cuts the core. The drilling fluid is usually circulated down around the outside of the drill and back up between the core and core barrel; the cuttings are stored in the downhole assembly, in a chamber above the core. When the core is retrieved, the cuttings chamber is emptied for the next run. Some drills have been designed to retrieve a second annular core outside the central core, and in these drills the space between the two cores can be used for circulation. Cable-suspended drills have proved to be the most reliable design for deep ice drilling.
Thermal drills, which cut ice by electrically heating the drill head, can also be used, but they have some disadvantages. Some have been designed for working in cold ice; they have high power consumption and the heat they produce can degrade the quality of the retrieved ice core. Early thermal drills, designed for use without drilling fluid, were limited in depth as a result; later versions were modified to work in fluid-filled holes but this slowed down trip times, and these drills retained the problems of the earlier models. In addition, thermal drills are typically bulky and can be impractical to use in areas where there are logistical difficulties. More recent modifications include the use of antifreeze, which eliminates the need for heating the drill assembly and hence reduces the power needs of the drill. Hot-water drills use jets of hot water at the drill head to melt the water around the core. The drawbacks are that it is difficult to accurately control the dimensions of the borehole, the core cannot easily be kept sterile, and the heat may cause thermal shock to the core.
When drilling in temperate ice, thermal drills have an advantage over electromechanical drills: ice melted by pressure can refreeze on EM drill bits, reducing cutting efficiency, and can clog other parts of the mechanism. EM drills are also more likely to fracture ice cores where the ice is under high stress.
When drilling deep holes, which require drilling fluid, the hole must be cased, since otherwise the drilling fluid will be absorbed by the snow and firn. The casing has to reach down to the impermeable ice layers. To install casing a shallow auger can be used to create a pilot hole, which is then reamed until it is wide enough to accept the casing; a large diameter auger can also be used, avoiding the need for reaming. An alternative to casing is to use water in the borehole to saturate the porous snow and firn; the water eventually turns to ice.
Ice cores from different depths are not all equally in demand by scientific investigators, which can lead to a shortage of ice cores at certain depths. To address this, work has been done on technology to drill replicate cores: additional cores, retrieved by drilling into the sidewall of the borehole, at depths of particular interest. Replicate cores were successfully retrieved at WAIS divide in the 2012–2013 drilling season, at four different depths.