Vault (architecture)
In architecture, a vault is a self-supporting arched form, usually of stone or brick, serving to cover a space with a ceiling or roof. As in building an arch, a temporary support is needed while rings of voussoirs are constructed and the rings placed in position. Until the topmost voussoir, the keystone, is positioned, the vault is not self-supporting. Where timber is easily obtained, this temporary support is provided by centering consisting of a framed truss with a semicircular or segmental head, which supports the voussoirs until the ring of the whole arch is completed.
The Mycenaeans were known for their tholos tombs, also called beehive tombs, which were underground structures with conical vaults. This type of vault is one of the earliest evidences of curved brick architecture without the use of stone arches, and its construction represented an innovative technique for covering circular spaces.
Vault types
Corbelled vaults, also called false vaults, with horizontally joined layers of stone have been documented since prehistoric times; in the 14th century BC from Mycenae. They were built regionally until modern times.The real vault construction with radially joined stones was already known to the Egyptians and Assyrians and was introduced into the building practice of the West by the Etruscans. The Romans in particular developed vault construction further and built barrel, cross and dome vaults. Some outstanding examples have survived in Rome, e.g. the Pantheon and the Basilica of Maxentius.
Brick vaults have been used in Egypt since the early 3rd millennium BC, and were widely used by the end of the 8th century BC, when Keystone vaults were built.”. However, monumental temple buildings of the pharaonic culture in the Nile Valley did not use vaults, since even the huge portals with widths of more than 7 meters were spanned with cut stone beams.
Dome
Amongst the earliest known examples of any form of vaulting is to be found in the Neolithic village of Khirokitia on Cyprus. Dating from BCE, the circular buildings supported beehive shaped corbel domed vaults of unfired mud-bricks and also represent the first evidence for settlements with an upper floor. Similar beehive tombs, called tholoi, exist in Crete and Northern Iraq. Their construction differs from that at Khirokitia in that most appear partially buried and make provision for a dromos entry.The inclusion of domes, however, represents a wider sense of the word vault. The distinction between the two is that a vault is essentially an arch which is extruded into the third dimension, whereas a dome is an arch revolved around its vertical axis.
Pitched brick barrel vault
Pitched-brick vaults are named for their construction, the bricks are installed vertically and are leaning at an angle: This allows their construction to be completed without the use of centering. Examples have been found in archaeological excavations in Mesopotamia dating to the 2nd and 3rd millennium BCE, which were set in gypsum mortar.Barrel vault
A barrel vault is the simplest form of a vault, semi-circular in cross-section, and resembles a barrel or tunnel cut lengthwise in half. The effect is that of a structure composed of continuous semicircular or pointed sections.The earliest known examples of barrel vaults were built by the Sumerians, possibly under the ziggurat at Nippur in Babylonia, which was built of fired bricks cemented with clay mortar.
The earliest barrel vaults in ancient Egypt are thought to be those in the granaries built by the 19th dynasty Pharaoh Ramesses II, the ruins of which are behind the Ramesseum, at Thebes. The span was and the lower part of the arch was built in horizontal courses, up to about one-third of the height, and the rings above were inclined back at a slight angle, so that the bricks of each ring, laid flatwise, adhered till the ring was completed, no centering of any kind being required; the vault thus formed was elliptic in section, arising from the method of its construction. A similar system of construction was employed for the vault over the great hall at Ctesiphon, where the material employed was fired bricks or tiles of great dimensions, cemented with mortar; but the span was close upon, and the thickness of the vault was nearly at the top, there being four rings of brickwork.
Assyrian palaces used pitched-brick vaults, made with sun-dried mudbricks, for gates, subterranean graves and drains. During the reign of king Sennacherib they were used to construct aqueducts, such as those at Jerwan. In the provincial city Dūr-Katlimmu they were used to create vaulted platforms. The tradition of their erection, however, would seem to have been handed down to their successors in Mesopotamia, viz. to the Sassanians, who in their palaces in Sarvestan and Firouzabad built domes of similar form to those shown in the Nimrud sculptures, the chief difference being that, constructed in rubble stone and cemented with mortar, they still exist, though probably abandoned on the Islamic invasion in the 7th century.
Groin vaults
A groin vault is formed by the intersection of two barrel vaults at right angles, resulting in the formation of angles or groins along the lines of transition between the webs. In these bays the longer transverse arches are semi-circular, as are the shorter longitudinal arches. The curvatures of these bounding arches were apparently used as the basis for the web centrings, which was created in the form of two intersecting tunnels as though each web was an arch projected horizontally in three dimensions.The earliest example is thought to be over a small hall at Pergamum, in Asia Minor, but its first employment over halls of great dimensions is due to the Romans. When two semicircular barrel vaults of the same diameter cross one another their intersection is known as a groin vault, down which the thrust of the vault is carried to the cross walls; if a series of two or more barrel vaults intersect one another, the weight is carried on to the piers at their intersection and the thrust is transmitted to the outer cross walls; thus in the Roman reservoir at Baiae, known as the Piscina Mirabilis, a series of five aisles with semicircular barrel vaults are intersected by twelve cross aisles, the vaults being carried on 48 piers and thick external walls. The width of these aisles being only about there was no great difficulty in the construction of these vaults, but in the Roman Baths of Caracalla the tepidarium had a span of, more than twice that of an English cathedral, so that its construction both from the statical and economical point of view was of the greatest importance.
The researches of M. Choisy, based on a minute examination of those portions of the vaults which still remain in situ, have shown that, on a comparatively slight centering, consisting of trusses placed about apart and covered with planks laid from truss to truss, were laid – to begin with – two layers of the Roman brick ; on these and on the trusses transverse rings of brick were built with longitudinal ties at intervals; on the brick layers and embedding the rings and cross ties concrete was thrown in horizontal layers, the haunches being filled in solid, and the surface sloped on either side and covered over with a tile roof of low pitch laid direct on the concrete. The rings relieved the centering from the weight imposed, and the two layers of bricks carried the concrete till it had set.
Image:Groin vault plan force.jpg|thumb|Plan of a groin vault from above showing resultant outward thrust
Image:Groin vault top.jpg|thumb|upright|Groin vault from above
As the walls carrying these vaults were also built in concrete with occasional bond courses of brick, the whole structure was homogeneous. One of the important ingredients of the mortar was a volcanic deposit found near Rome, known as pozzolana, which, when the concrete had set, not only made the concrete as solid as the rock itself, but to a certain extent neutralized the thrust of the vaults, which formed shells equivalent to that of a metal lid; the Romans, however, do not seem to have recognized the value of this pozzolana mixture, for they otherwise provided amply for the counteracting of any thrust which might exist by the erection of cross walls and buttresses. In the tepidaria of the Thermae and in the basilica of Constantine, in order to bring the thrust well within the walls, the main barrel vault of the hall was brought forward on each side and rested on detached columns, which constituted the principal architectural decoration. In cases where the cross vaults intersecting were not of the same span as those of the main vault, the arches were either stilted so that their soffits might be of the same height, or they formed smaller intersections in the lower part of the vault; in both of these cases, however, the intersections or groins were twisted, for which it was very difficult to form a centering, and, moreover, they were of disagreeable effect: though every attempt was made to mask this in the decoration of the vault by panels and reliefs modelled in stucco.
Rib vault
A rib vault is one in which all of the groins are covered by ribs or diagonal ribs in the form of segmental arches. Their curvatures are defined by the bounding arches. Whilst the transverse arches retain the same semi-circular profile as their groin-vaulted counterparts, the longitudinal arches are pointed with both arcs having their centres on the impost line. This allows the latter to correspond more closely to the curvatures of the diagonal ribs, producing a straight tunnel running from east to west.Reference has been made to the rib vault in Roman work, where the intersecting barrel vaults were not of the same diameter. Their construction must at all times have been somewhat difficult, but where the barrel vaulting was carried round over the choir aisle and was intersected by semicones instead of cylinders, it became worse and the groins more complicated. This would seem to have led to a change of system and to the introduction of a new feature, which completely revolutionized the construction of the vault. Hitherto the intersecting features were geometrical surfaces, of which the diagonal groins were the intersections, elliptical in form, generally weak in construction and often twisting. The medieval builder reversed the process, and set up the diagonal ribs first, which were utilized as permanent centres, and on these he carried his vault or web, which henceforward took its shape from the ribs. Instead of the elliptical curve which was given by the intersection of two semicircular barrel vaults, or cylinders, he employed the semicircular arch for the diagonal ribs; this, however, raised the centre of the square bay vaulted above the level of the transverse arches and of the wall ribs, and thus gave the appearance of a dome to the vault, such as may be seen in the nave of Sant'Ambrogio, Florence. To meet this, at first the transverse and wall ribs were stilted, or the upper part of their arches was raised, as in the Abbaye-aux-Hommes at Caen, and the Abbey of Lessay, in Normandy. The problem was ultimately solved by the introduction of the pointed arch for the transverse and wall ribs – the pointed arch had long been known and employed, on account of its much greater strength and of the less thrust it exerted on the walls. When employed for the ribs of a vault, however narrow the span might be, by adopting a pointed arch, its summit could be made to range in height with the diagonal rib; and, moreover, when utilized for the ribs of the annular vault, as in the aisle round the apsidal termination of the choir, it was not necessary that the half ribs on the outer side should be in the same plane as those of the inner side; for when the opposite ribs met in the centre of the annular vault, the thrust was equally transmitted from one to the other, and being already a broken arch the change of its direction was not noticeable.
Image:Fresco vault Gent.jpg|thumb|right|Rib vault of church Sint-Niklaaskerk in Ghent, Belgium
The first introduction of the pointed arch rib took place at Cefalù Cathedral and pre-dated the abbey of Saint-Denis. Whilst the pointed rib-arch is often seen as an identifier for Gothic architecture, Cefalù is a Romanesque cathedral whose masons experimented with the possibility of Gothic rib-arches before it was widely adopted by western church architecture. Besides Cefalù Cathedral, the introduction of the pointed arch rib would seem to have taken place in the choir aisles of the abbey of Saint-Denis, near Paris, built by the abbot Suger in 1135. It was in the church at Vezelay that it was extended to the square bay of the porch. As has been pointed out, the aisles had already in the early Christian churches been covered over with groined vaults, the only advance made in the later developments being the introduction of transverse ribs' dividing the bays into square compartments. In the 12th century the first attempts were made to vault over the naves, which were twice the width of the aisles, so it became necessary to include two bays of the aisles to form one rectangular bay in the nave. It followed that every alternate pier served no purpose, so far as the support of the nave vault was concerned, and this would seem to have suggested an alternative to provide a supplementary rib across the church and between the transverse ribs. This resulted in what is known as a sexpartite, or six-celled vault, of which one of the earliest examples is found in the Abbaye-aux-Hommes at Caen. This church, built by William the Conqueror, was originally constructed to carry a timber roof only, but nearly a century later the upper part of the nave walls were partly rebuilt, in order that it might be covered with a vault. The immense size, however, of the square vault over the nave necessitated some additional support, so that an intermediate rib was thrown across the church, dividing the square compartment into six cells, and called the sexpartite vault
The intermediate rib, however, had the disadvantage of partially obscuring one side of the clerestory windows, and it threw unequal weights on the alternate piers, so that in the cathedral of Soissons a quadripartite or four-celled vault was introduced, the width of each bay being half the span of the nave, and corresponding therefore with the aisle piers. To this there are some exceptions, in Sant' Ambrogio, Milan, and San Michele, Pavia, and in the cathedrals of Speyer, Mainz and Worms, where the quadripartite vaults are nearly square, the intermediate piers of the aisles being of much smaller dimensions. In England sexpartite vaults exist at Canterbury , Rochester, Lincoln, Durham, and St. Faith's chapel, Westminster Abbey.
In the earlier stage of rib vaulting, the arched ribs consisted of independent or separate voussoirs down to the springing; the difficulty, however, of working the ribs separately led to two other important changes: the lower part of the transverse diagonal and wall ribs were all worked out of one stone; and the lower horizontal, constituting what is known as the tas-de-charge or solid springer. The tas-de-charge, or solid springer, had two advantages: it enabled the stone courses to run straight through the wall, to bond the whole together much better; and it lessened the span of the vault, which then required a centering of smaller dimensions. As soon as the ribs were completed, the web or stone shell of the vault was laid on them. In some English work each course of stone was of uniform height from one side to the other; but, as the diagonal rib was longer than either the transverse or wall rib, the courses dipped towards the former, and at the apex of the vault were cut to fit one another. In the early English Gothic period, in consequence of the great span of the vault and the very slight rise or curvature of the web, it was thought better to simplify the construction of the web by introducing intermediate ribs between the wall rib and the diagonal rib and between the diagonal and the transverse ribs; and in order to meet the thrust of these intermediate ribs a ridge rib was required, and the prolongation of this rib to the wall rib hid the junction of the web at the summit, which was not always very sightly, and constituted the ridge rib. In France, on the other hand, the web courses were always laid horizontally, and they are therefore of unequal height, increasing towards the diagonal rib. Each course also was given a slight rise in the centre, so as to increase its strength; this enabled the French masons to dispense with the intermediate rib, which was not introduced by them till the 15th century, and then more as a decorative than a constructive feature, as the domical form given to the French web rendered unnecessary the ridge rib, which, with some few exceptions, exists only in England. In both English and French vaulting centering was rarely required for the building of the web, a template being employed to support the stones of each ring until it was complete. In Italy, Germany and Spain the French method of building the web was adopted, with horizontal courses and a domical form. Sometimes, in the case of comparatively narrow compartments, and more especially in clerestories, the wall rib was stilted, and this caused a peculiar twisting of the web, where the springing of the wall rib is at K: to these twisted surfaces the term ploughshare vaulting is given.
Image:Lienzingen-Liebfrauenkirche 1.jpg|thumb|Rib-vault ceiling, with Lierne ribs, of the Liebfrauenkirche, Mühlacker 1482
One of the earliest examples of the introduction of the intermediate rib is found in the nave of Lincoln Cathedral, and there the ridge rib is not carried to the wall rib. It was soon found, however, that the construction of the web was much facilitated by additional ribs, and consequently there was a tendency to increase their number, so that in the nave of Exeter Cathedral three intermediate ribs were provided between the wall rib and the diagonal rib. To mask the junction of the various ribs, their intersections were ornamented with richly carved bosses, and this practice increased on the introduction of another short rib, known as the lierne, a term in France given to the ridge rib. Lierne ribs are short ribs crossing between the main ribs, and were employed chiefly as decorative features, as, for instance, in the Liebfrauenkirche of Mühlacker, Germany. One of the best examples of Lierne ribs exists in the vault of the oriel window of Crosby Hall, London. The tendency to increase the number of ribs led to singular results in some cases, as in the choir of Gloucester Cathedral, where the ordinary diagonal ribs become mere ornamental mouldings on the surface of an intersected pointed barrel vault, and again in the cloisters, where the introduction of the fan vault, forming a concave-sided conoid, returned to the principles of the Roman geometrical vault. This is further shown in the construction of these fan vaults, for although in the earliest examples each of the ribs above the tas-de-charge was an independent feature, eventually it was found easier to carve them and the web out of the solid stone, so that the rib and web were purely decorative and had no constructional or independent functions.