United States customary units
United States customary units form a system of measurement units commonly used in the United States and most U.S. territories since being standardized and adopted in 1832. The United States customary system developed from English units that were in use in the British Empire before the U.S. became an independent country. The United Kingdom's system of measures evolved by 1824 to create the imperial system, with imperial units, which was officially adopted in 1826, changing the definitions of some of its units. Consequently, while many U.S. units are essentially similar to their imperial counterparts, there are noticeable differences between the systems.
The majority of U.S. customary units were redefined in terms of the meter and kilogram with the Mendenhall Order of 1893 and, in practice, for many years before. These definitions were refined by the international yard and pound agreement of 1959.
The United States uses customary units in commercial activities, as well as for personal and social use. In science, medicine, many sectors of industry, and some government and military areas, metric units are used. The International System of Units, the modern form of the metric system, is preferred for many uses by the U.S. National Institute of Standards and Technology. For newer types of measurement where there is no traditional customary unit, international units are used, sometimes mixed with customary units: for example, electrical resistivity of wire expressed in ohms per thousand feet.
History
The United States customary system of units of 1832 is based on the system in use in the United Kingdom prior to the introduction to the British imperial system on January 1, 1826. Both systems are derived from English units, an older system of units which had evolved over the millennia before American independence, and which had its roots in both Roman and Anglo-Saxon units.The customary system was championed by the U.S.-based International Institute for Preserving and Perfecting Weights and Measures in the late 19th century. Some advocates of the customary system saw the French Revolutionary, or metric, system as atheistic. The president of an Ohio auxiliary of the Institute wrote that the traditional units were "a just weight and a just measure, which alone are acceptable to the Lord". His organization later went so far as to publish music for a song proclaiming "down with every 'metric' scheme".
The U.S. government passed the Metric Conversion Act of 1975, which made the metric system "the preferred system of weights and measures for U.S. trade and commerce". The legislation states that the federal government has a responsibility to assist industry as it voluntarily converts to the metric system, i.e., metrification. This is most evident in U.S. labeling requirements on food products, where SI units are almost always presented alongside customary units. According to the CIA World Factbook, the United States is one of three nations that have not adopted the metric system as their official system of weights and measures.
Executive Order 12770, signed by President George H. W. Bush in July 1991, citing the Metric Conversion Act, directed departments and agencies within the executive branch of the United States Government to "take all appropriate measures within their authority" to use the metric system "as the preferred system of weights and measures for United States trade and commerce" and authorized the Secretary of Commerce "to charter an Interagency Council on Metric Policy, which will assist the Secretary in coordinating Federal Government-wide implementation of this order." Implementation has been limited. See Metrication in the United States.
U.S. customary units are widely used on consumer products and in industrial manufacturing. Metric units are standard in the fields of science, medicine, and engineering, as well as many sectors of industry and government, including the military. There are anecdotal objections to the use of metric units in carpentry and the building trades, on the basis that it is easier to remember an integer number of inches plus a fraction, rather than a measurement in millimeters, or that foot-inch measurements are more suitable when distances are frequently divided into halves, thirds, and quarters, often in parallel. The metric system also lacks a parallel measurement to the foot.
The term "United States customary units" was used by the former United States National Bureau of Standards, although "English units" is sometimes used in colloquial speech.
Length
For measuring length, the U.S. customary system uses the inch, foot, yard, and mile, which are the only four customary length measurements in everyday use. From 1893, the foot was legally defined as exactly, approximately. Since July 1, 1959, the units of length have been defined on the basis of =, which makes the foot exactly .The U.S., the United Kingdom and other Commonwealth countries agreed on this definition per the International Yard and Pound Agreement of 1958. At the time of the agreement, the basic geodetic datum in North America was the North American Datum of 1927, which had been constructed by triangulation based on the definition of the foot in the Mendenhall Order of 1893, that is = : this definition was retained for data derived from NAD27, but renamed the US survey foot to distinguish it from the international foot.
For most applications, the difference between the two definitions is insignificant – one international foot is exactly of a US survey foot, for a difference of about per mile – but it affects the definition of the State Plane Coordinate Systems, which can stretch over hundreds of miles.
The NAD27 was replaced in the 1980s by the North American Datum of 1983, which is defined in meters. The SPCSs were also updated, but the U.S. National Geodetic Survey left the decision of which, if any, definition of the foot to use to the individual states and other jurisdictions. All SPCS 1983 systems are defined in meters, but forty jurisdictions also use the survey foot, six use the international foot, and ten do not specify which, if any, foot type should be used.
In 2019, the NIST, working with the National Geodetic Survey, National Ocean Service, National Oceanic and Atmospheric Administration and Department of Commerce, issued a Federal Register Notice indicating the deprecation of the U.S. survey foot and U.S. survey mile units from December 31, 2022.
In the following tables in this and subsequent sections, the most common measures are shown in italics, and approximate values are shown in parentheses; values not in parentheses are exact.
International units
International nautical units
US survey units
Note that as announced by the National Institute of Standards and Technology, the US survey foot, and other units defined in terms of it, have been deprecated since 2023, "except for historic and legacy applications".Area
The most widely used area unit with a name unrelated to any length unit is the acre. The National Institute of Standards and Technology formerly contended that customary area units are defined in terms of the square survey foot, not the square international foot. From 2023, it states that "although historically defined using the U.S. survey foot, the statute mile can be defined using either definition of the foot, as is the case for all other units listed in this table. However, use of definitions based on the U.S. survey foot should be avoided after December 31, 2022 except for historic and legacy applications."Volume
| Unit | Name | Divisions | SI equivalent |
| cubic inch | |||
| cubic foot | |||
| cubic yard | |||
| acre-foot |
The cubic inch, cubic foot and cubic yard are commonly used for measuring volume. There is one group of units for measuring volumes of liquids, based on the wine gallon and subdivisions of the fluid ounce, and one for measuring volumes of dry material, each with their own names and sub-units.
The units and their names are similar to the units in the imperial system, and many units are shared between the two systems as a whole. With respect to volume, this differs. The independence of the U.S. from the British Empire decades prior to the reformation of units in 1824—most notably the gallon, its subdivisions, and higher combinations above the pound—is the cause of the differences in values.
As a non-participant in that reform, the U.S. retained the separate systems for measuring the volumes of liquids and dry material, whereas the imperial system had unified the units for both under a new imperial gallon. The U.S. uses the pre-1824 gallon and Winchester bushel, as opposed to British 1824 definition of of water and the bushel as.
Fluid volume
One US fluid ounce is of a US pint, of a US quart, and of a US gallon. The teaspoon, tablespoon, and cup are defined in terms of a fluid ounce as,, and 8 fluid ounces respectively. The fluid ounce derives its name originally from being the volume of one ounce avoirdupois of water, but in the US it is defined as of a US gallon. Consequently, a fluid ounce of water weighs about 1.041 ounces avoirdupois.For nutritional labeling and medicine in the US, the teaspoon and tablespoon are defined as a metric teaspoon and tablespoonprecisely and respectively.
The saying, "a pint's a pound the world around", refers to 16 US fluid ounces of water weighing approximately one pound avoirdupois. An imperial pint of water weighs a pound and a quarter.
There are varying standards for barrel for some specific commodities, including 31 gallons for beer, 40 gallons for whiskey or kerosene, and 42 gallons for petroleum. The general standard for liquids is 31.5 gal or half a hogshead. The common 55-gallon size of drum for storing and transporting various products and wastes is sometimes confused with a barrel, though it is not a standard measure.
In the U.S., single servings of beverages are usually measured in fluid ounces. Milk is usually sold in half-pints, pints, quarts, half gallons, and gallons. Water volume for sinks, bathtubs, ponds, swimming pools, etc., is usually stated in gallons or cubic feet. Quantities of gases are usually given in cubic feet.
Minims, drams, gill, and pottle are rarely used currently. The gill is often referred to as a "half-cup". The pottle is often referred to as a "half-gallon".