OBD-II PIDs
OBD-II PIDs are codes used to request data from a vehicle, used as a diagnostic tool.
SAE standard J1979 defines many OBD-II PIDs. All on-road vehicles and trucks sold in North America are required to support a subset of these codes, primarily for state mandated emissions control|emissions] inspections. Manufacturers also define additional PIDs specific to their vehicles. Though not mandated, many motorcycles also support OBD-II PIDs.
In 1996, light duty vehicles were the first to be mandated followed by medium duty vehicles in 2005. They are both required to be accessed through a standardized data link connector defined by SAE J1962.
Heavy duty vehicles made after 2010, for sale in the US are allowed to support OBD-II diagnostics through SAE standard J1939-13 according to CARB in title 13 CCR 1971.1. Some heavy duty trucks in North America use the SAE J1962 OBD-II diagnostic connector that is common with passenger cars, notably Mack and Volvo Trucks, however they use 29 bit CAN identifiers.
Services / Modes
There are 10 diagnostic services described in the latest OBD-II standard SAE J1979. Before 2002, J1979 referred to these services as "modes". They are as follows:| Service / Mode | Description |
| [#Service 01|] | Show current data |
| [#Service 02|] | Show freeze frame data |
| [#Service 03|] | Show stored Diagnostic Trouble Codes |
| [#Service 04|] | Clear Diagnostic Trouble Codes and stored values |
| [#Service 05|] | Test results, oxygen sensor monitoring |
| Test results, other component/system monitoring | |
| Show pending Diagnostic Trouble Codes | |
| Control operation of on-board component/system | |
| [#Service 09|] | Request vehicle information |
| Permanent Diagnostic Trouble Codes |
Vehicle manufacturers are not required to support all services. Each manufacturer may define additional services above #9 for other information e.g. the voltage of the traction battery in a hybrid electric vehicle.
The nonOBD UDS services start at 0x10 to avoid overlap of ID-range.
Standard PIDs
The table below shows the standard OBD-II PIDs as defined by SAE J1979. The expected response for each PID is given, along with information on how to translate the response into meaningful data. Again, not all vehicles will support all PIDs and there can be manufacturer-defined custom PIDs that are not defined in the OBD-II standard.Note that services 01 and 02 are basically identical, except that service 01 provides current information, whereas service 02 provides a snapshot of the same data taken at the point when the last diagnostic trouble code was set. The exceptions are PID 01, which is only available in service 01, and PID 02, which is only available in service 02. If service 02 PID 02 returns zero, then there is no snapshot and all other service 02 data is meaningless.
When using Bit-Encoded-Notation, quantities like C4 means bit 4 from data byte C. Each bit is numbered from 0 to 7, so 7 is the most significant bit and 0 is the least significant bit.
Service - Show current data
Service - Show freeze frame data
Service accepts the same PIDs as service, with the same meaning, but information given is from when the freeze frame was created. Note that PID is used to obtain the DTC that triggered the freeze frame.A person has to send the frame number in the data section of the message.
Service - Show stored Diagnostic Trouble Codes (DTCs)
Service - Clear Diagnostic Trouble Codes and stored values
Service - Test results, oxygen sensor monitoring (non CAN only)
Service - Request vehicle information
Bitwise encoded PIDs
Some of the PIDs in the above table cannot be explained with a simple formula. A more elaborate explanation of these data is provided here:Service 01 PID - Show PIDs supported
A request for this PID returns 4 bytes of data. Each bit, from MSB to LSB, represents one of the next 32 PIDs and specifies whether that PID is supported.For example, if the car response is, it can be decoded like this:
So, supported PIDs are:,,,,,,,,,,,,,,, and
Service 01 PID - Monitor status since DTCs cleared
A request for this PID returns 4 bytes of data, labeled A, B, C and D.The first byte contains two pieces of information. Bit indicates whether or not the MIL is illuminated. Bits through represent the number of diagnostic trouble codes currently flagged in the ECU.
The second, third, and fourth bytes give information about the availability and completeness of certain on-board tests. The third and fourth bytes are to be interpreted differently depending upon whether the engine is spark ignition or compression ignition. In the second byte, bit indicates the engine type and thus how to interpret bytes C and D, with being spark and being compression. Bits to and to are used for information about tests that not engine-type specific, and thus termed common tests. Note that for bits indicating test availability a bit set to indicates available, whilst for bits indicating test completeness a bit set to indicates complete.
| Bits | Definition |
| State of the CEL/MIL. | |
| - | Number of confirmed emissions-related DTCs available for display. |
| Reserved | |
| - | Bitmap indicating completeness of common tests. |
| Indication of engine type = Spark ignition = Compression ignition | |
| - | Bitmap indicating availability of common tests. |
| - | Bitmap indicating availability of engine-type specific tests. |
| - | Bitmap indicating completeness of engine-type specific tests. |
Bits from byte B representing common test indicators are mapped as follows:
| Test availability | Test completeness | |
| Components | ||
| Fuel System | ||
| Misfire |
Bytes C and D are mapped as follows for spark ignition engine types :
| Test availability | Test completeness | |
| EGR and/or VVT System | ||
| Oxygen Sensor Heater | ||
| Oxygen Sensor | ||
| Gasoline Particulate Filter | ||
| Secondary Air System | ||
| Evaporative System | ||
| Heated Catalyst | ||
| Catalyst |
Bytes C and D are alternatively mapped as follows for compression ignition engine types :
| Test availability | Test completeness | |
| EGR and/or VVT System | ||
| PM filter monitoring | ||
| Exhaust Gas Sensor | ||
| - Reserved - | ||
| Boost Pressure | ||
| - Reserved - | ||
| NOx/SCR Monitor | ||
| NMHC Catalyst |
Service 01 PID - Monitor status this drive cycle
A request for this PID returns 4 bytes of data. The data returned is of an identical form to that returned for PID, with one exception - the first byte is always zero.Service 01 PID 78 and 79 - Exhaust Gas temperature (EGT) Bank 1 and Bank 2
A request for one of these two PIDs will return 9 bytes of data. PID returns data relating to EGT sensors for bank 1, whilst PID similarly returns data for bank 2. The first byte is a bit encoded field indicating which EGT sensors are supported for the respective bank.| Bytes | Description |
| EGT sensor support | |
| - | Temperature read by EGT sensor 1 |
| - | Temperature read by EGT sensor 2 |
| - | Temperature read by EGT sensor 3 |
| - | Temperature read by EGT sensor 4 |
The first byte is bit-encoded as follows:
| Bits | Description |
| - | Reserved |
| EGT sensor 4 supported? | |
| EGT sensor 3 supported? | |
| EGT sensor 2 supported? | |
| EGT sensor 1 supported? |
Bytes B through I provide 16-bit integers indicating the temperatures of the sensors. The temperature values are interpreted in degrees Celsius in the range -40 to 6513.5, using the usual formula. Only values for which the corresponding sensor is supported are meaningful.
Service 03 (no PID required) - Show stored Diagnostic Trouble Codes
A request for this service returns a list of the DTCs that have been set. The list is encapsulated using the ISO 15765-2 protocol.If there are two or fewer DTCs then they are returned in an ISO-TP Single Frame. Three or more DTCs in the list are reported in multiple frames, with the exact count of frames dependent on the communication type and addressing details.
Each trouble code requires 2 bytes to describe. Encoded in these bytes are a category and a number. It is typically shown decoded into a five-character form like "", where the first character represents the category the DTC belongs to, and the remaining four characters are a hexadecimal representation of the number under that category. The first two bits of the first byte represent the category. The remaining 14 bits represent the number. Of note is that since the second character is formed from only two bits, it can thus only be within the range -.
| Bits | Definition |
| - | Category : - Powertrain : - Chassis : - Body : - Network |
| - | Number |
An example DTC of "" would be decoded as follows:
The resulting five-character code, e.g. "", can be looked up in a table of OBD-II DTCs to get an actual description of what it represents. Of note, whilst some blocks of DTC code ranges have generic meanings that apply to all vehicles and manufacturers, the meanings of others can vary per manufacturer or even model.
It is also worth noting that DTCs may sometimes be encountered in a four-character form, e.g. "", which is simply the plain hexadecimal representation of the two bytes, with proper decoding with respect to the category not having been performed.
Service 09 PID 08 - In-use performance tracking for spark ignition engines
It provides information about track in-use performance for catalyst banks, oxygen sensor banks, evaporative leak detection systems, EGR systems and secondary air system.The numerator for each component or system tracks the number of times that all conditions necessary for a specific monitor to detect a malfunction have been encountered.
The denominator for each component or system tracks the number of times that the vehicle has been operated in the specified conditions.
The count of data items should be reported at the beginning.
All data items of the In-use Performance Tracking record consist of two bytes and are reported in this order.
| Mnemonic | Description |
| OBDCOND | OBD Monitoring Conditions Encountered Counts |
| IGNCNTR | Ignition Counter |
| CATCOMP1 | Catalyst Monitor Completion Counts Bank 1 |
| CATCOND1 | Catalyst Monitor Conditions Encountered Counts Bank 1 |
| CATCOMP2 | Catalyst Monitor Completion Counts Bank 2 |
| CATCOND2 | Catalyst Monitor Conditions Encountered Counts Bank 2 |
| O2SCOMP1 | O2 Sensor Monitor Completion Counts Bank 1 |
| O2SCOND1 | O2 Sensor Monitor Conditions Encountered Counts Bank 1 |
| O2SCOMP2 | O2 Sensor Monitor Completion Counts Bank 2 |
| O2SCOND2 | O2 Sensor Monitor Conditions Encountered Counts Bank 2 |
| EGRCOMP | EGR Monitor Completion Condition Counts |
| EGRCOND | EGR Monitor Conditions Encountered Counts |
| AIRCOMP | AIR Monitor Completion Condition Counts |
| AIRCOND | AIR Monitor Conditions Encountered Counts |
| EVAPCOMP | EVAP Monitor Completion Condition Counts |
| EVAPCOND | EVAP Monitor Conditions Encountered Counts |
| SO2SCOMP1 | Secondary O2 Sensor Monitor Completion Counts Bank 1 |
| SO2SCOND1 | Secondary O2 Sensor Monitor Conditions Encountered Counts Bank 1 |
| SO2SCOMP2 | Secondary O2 Sensor Monitor Completion Counts Bank 2 |
| SO2SCOND2 | Secondary O2 Sensor Monitor Conditions Encountered Counts Bank 2 |
Service 09 PID 0B - In-use performance tracking for compression ignition engines
It provides information about track in-use performance for NMHC catalyst, NOx catalyst monitor, NOx adsorber monitor, PM filter monitor, exhaust gas sensor monitor, EGR/ VVT monitor, boost pressure monitor and fuel system monitor.All data items consist of two bytes and are reported in this order :
| Mnemonic | Description |
| OBDCOND | OBD Monitoring Conditions Encountered Counts |
| IGNCNTR | Ignition Counter |
| HCCATCOMP | NMHC Catalyst Monitor Completion Condition Counts |
| HCCATCOND | NMHC Catalyst Monitor Conditions Encountered Counts |
| NCATCOMP | NOx/SCR Catalyst Monitor Completion Condition Counts |
| NCATCOND | NOx/SCR Catalyst Monitor Conditions Encountered Counts |
| NADSCOMP | NOx Adsorber Monitor Completion Condition Counts |
| NADSCOND | NOx Adsorber Monitor Conditions Encountered Counts |
| PMCOMP | PM Filter Monitor Completion Condition Counts |
| PMCOND | PM Filter Monitor Conditions Encountered Counts |
| EGSCOMP | Exhaust Gas Sensor Monitor Completion Condition Counts |
| EGSCOND | Exhaust Gas Sensor Monitor Conditions Encountered Counts |
| EGRCOMP | EGR and/or VVT Monitor Completion Condition Counts |
| EGRCOND | EGR and/or VVT Monitor Conditions Encountered Counts |
| BPCOMP | Boost Pressure Monitor Completion Condition Counts |
| BPCOND | Boost Pressure Monitor Conditions Encountered Counts |
| FUELCOMP | Fuel Monitor Completion Condition Counts |
| FUELCOND | Fuel Monitor Conditions Encountered Counts |
Enumerated PIDs
Some PIDs are to be interpreted specially, and aren't necessarily exactly bitwise encoded, or in any scale.The values for these PIDs are enumerated.
Service 01 PID - Fuel system status
A request for this PID returns 2 bytes of data. The first byte describes fuel system #1. The second byte describes fuel system #2 and is encoded identically to the first byte. The meaning assigned to the value of each byte is as follows:| Value | Description |
| 0 | The motor is off |
| 1 | Open loop due to insufficient engine temperature |
| 2 | Closed loop, using oxygen sensor feedback to determine fuel mix |
| 4 | Open loop due to engine load OR fuel cut due to deceleration |
| 8 | Open loop due to system failure |
| 16 | Closed loop, using at least one oxygen sensor but there is a fault in the feedback system |
Any other value is an invalid response.
Service 01 PID - Commanded secondary air status
A request for this PID returns a single byte of data which describes the secondary air status.| Value | Description |
| 1 | Upstream |
| 2 | Downstream of catalytic converter |
| 4 | From the outside atmosphere or off |
| 8 | Pump commanded on for diagnostics |
Any other value is an invalid response.
Service 01 PID - OBD standards this vehicle conforms to
A request for this PID returns a single byte of data which describes which OBD standards this ECU was designed to comply with. The different values the data byte can hold are shown below, next to what they mean:| Value | Description |
| 1 | OBD-II as defined by the CARB |
| 2 | OBD as defined by the EPA |
| 3 | OBD and OBD-II |
| 4 | OBD-I |
| 5 | Not OBD compliant |
| 6 | EOBD |
| 7 | EOBD and OBD-II |
| 8 | EOBD and OBD |
| 9 | EOBD, OBD and OBD II |
| 10 | JOBD |
| 11 | JOBD and OBD II |
| 12 | JOBD and EOBD |
| 13 | JOBD, EOBD, and OBD II |
| 14 | Reserved |
| 15 | Reserved |
| 16 | Reserved |
| 17 | Engine Manufacturer Diagnostics |
| 18 | Engine Manufacturer Diagnostics Enhanced |
| 19 | Heavy Duty On-Board Diagnostics |
| 20 | Heavy Duty On-Board Diagnostics |
| 21 | World Wide Harmonized OBD |
| 22 | Reserved |
| 23 | Heavy Duty Euro OBD Stage I without NOx control |
| 24 | Heavy Duty Euro OBD Stage I with NOx control |
| 25 | Heavy Duty Euro OBD Stage II without NOx control |
| 26 | Heavy Duty Euro OBD Stage II with NOx control |
| 27 | Reserved |
| 28 | Brazil OBD Phase 1 |
| 29 | Brazil OBD Phase 2 |
| 30 | Korean OBD |
| 31 | India OBD I |
| 32 | India OBD II |
| 33 | Heavy Duty Euro OBD Stage VI |
| 34-250 | Reserved |
| 251-255 | Not available for assignment |
Service 01 PID - Fuel Type Coding
This PID returns a value from an enumerated list giving the fuel type of the vehicle. The fuel type is returned as a single byte, and the value is given by the following table:| Value | Description |
| 0 | Not available |
| 1 | Gasoline |
| 2 | Methanol |
| 3 | Ethanol |
| 4 | Diesel |
| 5 | LPG |
| 6 | CNG |
| 7 | Propane |
| 8 | Electric |
| 9 | Bifuel running Gasoline |
| 10 | Bifuel running Methanol |
| 11 | Bifuel running Ethanol |
| 12 | Bifuel running LPG |
| 13 | Bifuel running CNG |
| 14 | Bifuel running Propane |
| 15 | Bifuel running Electricity |
| 16 | Bifuel running electric and combustion engine |
| 17 | Hybrid gasoline |
| 18 | Hybrid Ethanol |
| 19 | Hybrid Diesel |
| 20 | Hybrid Electric |
| 21 | Hybrid running electric and combustion engine |
| 22 | Hybrid Regenerative |
| 23 | Bifuel running diesel |
Any other value is reserved by ISO/SAE. There are currently no definitions for flexible-fuel vehicle.
Non-standard PIDs
The majority of all OBD-II PIDs in use are non-standard. For most modern vehicles, there are many more functions supported on the OBD-II interface than are covered by the standard PIDs, and there is relatively minor overlap between vehicle manufacturers for these non-standard PIDs.There is very limited information available in the public domain for non-standard PIDs. The primary source of information on non-standard PIDs across different manufacturers is maintained by the US-based Equipment and Tool Institute and only available to members. The price of ETI membership for access to scan codes varies based on company size defined by annual sales of automotive tools and equipment in North America:
| Annual Sales in North America | Annual Dues |
| Under $10,000,000 | $5,000 |
| $10,000,000 - $50,000,000 | $7,500 |
| Greater than $50,000,000 | $10,000 |
However, even ETI membership will not provide full documentation for non-standard PIDs. ETI states:
Some OEMs refuse to use ETI as a one-stop source of scan tool information. They prefer to do business with each tool company separately. These companies also require that you enter into a contract with them. The charges vary but here is a snapshot as of April 13th, 2015 of the per year charges:
GM $50,000 Honda $5,000 Suzuki $1,000 BMW $25,500 plus $2,000 per update. Updates occur annually.
CAN (11-bit) bus format
As defined in ISO 15765-4, emissions protocols use the ISO-TP transport layer. All CAN frames sent using ISO-TP use a data length of 8 bytes. It is recommended to pad the unused data bytes with 0xCC.The PID query and response occurs on the vehicle's CAN bus. Standard OBD requests and responses use functional addresses. The diagnostic reader initiates a query using CAN ID 7DFh, which acts as a broadcast address, and accepts responses from any ID in the range 7E8h to 7EFh. ECUs that can respond to OBD queries listen both to the functional broadcast ID of 7DFh and one assigned ID in the range 7E0h to 7E7h. Their response has an ID of their assigned ID plus 8 e.g. 7E8h through 7EFh.
This approach allows up to eight ECUs, each independently responding to OBD queries. The diagnostic reader can use the ID in the ECU response frame to continue communication with a specific ECU. In particular, multi-frame communication requires a response to the specific ECU ID rather than to ID 7DFh.
CAN bus may also be used for communication beyond the standard OBD messages. Physical addressing uses particular CAN IDs for specific modules with proprietary frame payloads.
Query
The functional PID query is sent to the vehicle on the CAN bus at ID 7DFh, using 8 data bytes. The bytes are:Response
The vehicle responds to the PID query on the CAN bus with message IDs that depend on which module responded. Typically the engine or main ECU responds at ID 7E8h. Other modules, like the hybrid controller or battery controller in a Prius, respond at 07E9h, 07EAh, 07EBh, etc. These are 8h higher than the physical address the module responds to. Even though the number of bytes in the returned value is variable, the message uses 8 data bytes regardless.The bytes are: