Surface acoustic wave
A surface acoustic wave is an acoustic wave traveling along the surface of a material exhibiting elasticity, with an amplitude that typically decays exponentially with depth into the material, such that they are confined to a depth of about one wavelength.
Discovery
SAWs were first explained in 1885 by Lord Rayleigh, who described the surface acoustic mode of propagation and predicted its properties in his classic paper. Named after their discoverer, Rayleigh waves have a longitudinal and a vertical shear component that can couple with any media like additional layers in contact with the surface. This coupling strongly affects the amplitude and velocity of the wave, allowing SAW sensors to directly sense mass and mechanical properties. The term 'Rayleigh waves' is often used synonymously with 'SAWs', although strictly speaking there are multiple types of surface acoustic waves, such as Love waves, which are shear waves polarised in the plane of the surface, rather than waves having longitudinal and shear vertical components.SAWs such as Love and Rayleigh waves tend to propagate for much longer than bulk waves, as they only have to travel in two dimensions, rather than in three. Furthermore, in general they have a lower velocity than their bulk counterparts.
SAW devices
Surface acoustic wave devices provide wide-range of applications with the use of electronic system, including delay lines, filters, correlators and DC to DC converters. The possibilities of these SAW device could provide potential field in radar and communication systems.Application in electronic components
This kind of wave is commonly used in devices called SAW devices in electronic circuits. SAW devices are used as filters, oscillators and transformers, devices that are based on the transduction of acoustic waves. The transduction from electric energy to mechanical energy is accomplished by the use of piezoelectric materials.Image:SAW device.png|right|thumb|250px|Schematic picture of a typical SAW device design
Electronic devices employing SAWs normally use one or more interdigital transducers to convert acoustic waves to electrical signals and vice versa by exploiting the piezoelectric effect of certain materials, like quartz, lithium niobate, lithium tantalate, lanthanum gallium silicate, etc. These devices are fabricated by substrate cleaning/treatments like polishing, metallisation, photolithography, and passivation/protection layer manufacturing. These are typical process steps used in manufacturing of semiconductors like silicon integrated circuits.
All parts of the device have effect on the performance of the SAW devices because propagation of Rayleigh waves is highly dependent on the substrate material surface, its quality and all layers in contact with the substrate. For example in SAW filters the sampling frequency is dependent on the width of the IDT fingers, the power handling capability is related to the thickness and materials of the IDT fingers, and the temperature stability depends not only of the temperature behavior of the substrate but also on the metals selected for the IDT electrodes and the possible dielectric layers coating the substrate and the electrodes.
SAW filters are now used in mobile telephones, and provide technical advantages in performance, cost, and size over other filter technologies such as quartz crystals, LC filters, and waveguide filters specifically at frequencies below 1.5-2.5 GHz depending on the RF power needed to be filtered. Complementing technology to SAW for frequencies above 1.5-2.5 GHz is based on thin-film bulk acoustic resonators.
Much research has been done in the last 20 years in the area of surface acoustic wave sensors.
Sensor applications include all areas of sensing. SAW sensors have seen relatively modest commercial success to date, but are commonly commercially available for some applications such as touchscreen displays. They have been successfully applied to torque sensing in motorsport powertrains and high performance aerospace applications as well as temperature sensing in harsh environments such as high voltage electrical power transmission and the combined sensing of torque and temperature on the rotor of electric motors
SAW device applications in radio and television
SAW resonators are used in many of the same applications in which quartz crystals are used, because they can operate at higher frequency. They are often used in radio transmitters where tunability is not required. They are often used in applications such as garage door opener remote controls, short range radio frequency links for computer peripherals, and other devices where channelization is not required. Where a radio link might use several channels, quartz crystal oscillators are more commonly used to drive a phase locked loop. Since the resonant frequency of a SAW device is set by the mechanical properties of the crystal, it does not drift as much as a simple LC oscillator, where conditions such as capacitor performance and battery voltage will vary substantially with temperature and age.SAW filters are also often used in radio receivers, as they can have precisely determined and narrow passbands. This is helpful in applications where a single antenna must be shared between a transmitter and a receiver operating at closely spaced frequencies. SAW filters are also frequently used in television receivers, for extracting subcarriers from the signal; until the analog switchoff, the extraction of digital audio subcarriers from the intermediate frequency strip of a television receiver or video recorder was one of the main markets for SAW filters.
Early pioneer Jeffery Collins incorporated surface acoustic wave devices in a Skynet receiver he developed in the 1970s. It synchronised signals faster than existing technology.
They are also often used in digital receivers, and are well suited to superhet applications. This is because the intermediate frequency signal is always at a fixed frequency after the local oscillator has been mixed with the received signal, and so a filter with a fixed frequency and high Q provides excellent removal of unwanted or interference signals.
In these applications, SAW filters are almost always used with a phase locked loop synthesized local oscillator, or a varicap driven oscillator.
SAW in geophysics
In seismology surface acoustic waves could become the most destructive type of seismic wave produced by earthquakes, which propagate in more complex media, such as ocean bottom, rocks, etc. so that it need to be noticed and monitored by people to protect living environment.SAW in weighing
Surface Acoustic Wave technology has been adapted for high-precision industrial weighing by leveraging the same piezoelectric principles used in electronic filters and sensors. In weighing systems, SAW transducers generate and measure acoustic waves along a precisely engineered substrate, allowing for extremely accurate deformation detection under load. This enables resolution levels far exceeding those of traditional strain gauge systems while maintaining superior durability and temperature stability. The inherent stability of SAW devices—rooted in their fixed mechanical resonance—results in weighing systems that require less frequent calibration and deliver consistent performance in demanding industrial environments. Arlyn Scales has pioneered the use of SAW in rugged scale platforms, offering 10x to 20x higher readability compared to conventional designs, without the fragility or cost associated with other high-precision technologies.SAW in quantum acoustics
SAWs play a key role in the field of quantum acoustics where, in contrast to quantum optics which studies the interaction between matter and light, the interaction between quantum systems and acoustic waves is analysed. The propagation speed of the respective waves of QA is five orders of magnitude slower than that of QO. As a result, QA offers a different perspective of the quantum regime in terms of wavelengths which QO has not covered. One example of these additions is the quantum optical investigation of qubits and quantum dots fabricated in such a way as to emulate essential aspects of natural atoms, e.g. energy-level structures and coupling to an electromagnetic field. These artificial atoms are arranged into a circuit dubbed 'giant atoms', due to its size reaching 10−4–10−3 m. Quantum optical experiments generally made use of microwave fields for matter-light interaction, but because of the difference of wavelength between the giant atoms and microwave fields, the latter of which has a wavelength ranging between 10−2–10−1 m, SAWs were used instead for their more suitable wavelength.Within the fields of magnonics and spintronics, a resonant coupling between spin waves and surface acoustic waves with equal wave-vector and frequency allows for the transfer of energy from one form to another, in either direction. This can for example be useful in the construction of magnetic field sensors, which are sensitive to both the intensity and direction of external magnetic fields. These sensors, constructed using a structure of magnetostrictive and piezoelectric layers have the benefit of operating without batteries and wires, as well as having a broad range of operating conditions, such as high temperatures or rotating systems.