Jeep CJ
The Jeep CJ models are a series and a range of small, open-bodied off-road vehicles and compact pickup trucks, built and sold by several successive incarnations of the Jeep automobile marque from 1945 through 1986. The 1945 Willys "Universal Jeep" was the world's first mass-produced civilian four-wheel drive car.
In 1944, Willys-Overland, the primary manufacturer of the World War II military Jeep, built prototypes for a commercial version – the CJ, short for "civilian Jeep". The design was a direct evolution from the wartime Jeep, but the most obvious change was adding a tailgate, and relocating the spare wheel to the side. Also, besides adding basic civilian amenities and options and legally-compliant lighting, the CJ required a sturdier drivetrain than the wartime model, because the targeted rural buyers would expect years of durability, instead of mere weeks as during WWII.
From then on, all CJ Jeeps consistently had a separate body and frame, rigid live axles with leaf springs both front and rear, a tapering nose design with flared fenders, and a fold-flat windshield, and could be driven without doors. Also, with few exceptions, they had part-time four-wheel drive systems, with the choice of high and low gearing, and open bodies with removable hard or soft tops. A few stand-out changes during 42 model years were the introductions of round-fendered vs. flat-fendered bodies, straight-6 and V8 engines, automatic gearboxes, and different 4-wheel drive systems. The 1976 CJ-7 stretched the wheelbase by, and made doors and a removable hardtop common items.
After remaining in production through a range of model numbers and several corporate parents, the Jeep CJ line was officially ended after 1986. More than 1.5 million CJ Jeeps were built, having continued the same basic body style for 45 years since the Jeep first appeared. Widely regarded as "America's workhorse", the CJs have been described as "probably the most successful utility vehicle ever made." American Motors VP Joseph E. Cappy said the end of "CJ production will signal an end of a very important era in Jeep history." In 1987, the Jeep CJ-7 was replaced by the first-generation Jeep Wrangler. Looking very similar and riding on the same wheelbase as the CJ-7, it carried over some important components, including its use of leaf springs.
A similar model, the DJ "Dispatcher", was introduced in 1956 as a two-wheel drive version with open, fabric, or a closed steel body in both left- and right-hand drives for hotel, resort, police, and later United States Postal Service markets.
CJ-1
In 1942, the US Department of Agriculture tested the MB. By 1944, the Allies were confident the war would be won, and wartime production looked to be winding down. This allowed Willys to consider designing a Jeep for the postwar civilian market. Documentation is scarce, but in early 1944, Willys seemed to have found time to start drawing up plans, and one or two prototypes dubbed CJ, for "Civilian Jeep", were running by May of that year. The first CJs had apparently been created by quick modification of the regular military MB, adding a tailgate, lower gearing, a drawbar, and a civilian-style canvas top. The first CJ served as a quick proof-of-concept test, and when a further design evolution materialized, it probably became the CJ-1 by default. They were manufactured until the CJ-2s appeared, and they were the first Jeeps built from the ground up for civilian use.No CJ-1s built have survived, and how many were made is unknown.
CJ-2
Although at least 40 were built, the Willys-Overland CJ-2 was not available for retail sale. The CJ-2s, also known as "AgriJeeps", were the second-generation prototypes for the first production civilian Jeep, and were used solely for testing purposes. Although their design was directly based on the military Willys MB, using the same Willys Go Devil engine, they were not only stripped of all military features, particularly the blackout lighting, but also the CJ-2s had many significant differences in body features and construction versus the military Jeep. They had tailgates, power take-offs, engine governors, column-shift T90 manual transmissions, 5.38 gears, 2.43:1 low-range transfer cases, and driver's-side tool indentations. Rear wheelwells were redesigned so that seats could be enlarged, improved, and moved rearward, and new, more weather-tight top designs were tried. A canvas half-top with roll-down doors was one of several top designs tried before production. The CJ-2 Go-Devil L-head engine was largely the same as the wartime Jeep, but used a different carburetor and ignition system.Later models were stamped "JEEP" and were painted in a few civilian colors that translated into the "WILLYS" stamping and the colors that appeared on the first production CJ-2A Jeeps built from 1945. The spare tire was mounted forward of the passenger-side rear wheel on the earlier models and aft of the rear wheel on later ones. The CJ-2s were likely distributed to "agricultural stations" for evaluation purposes.
Of the 40–45 CJ-2s built, serial numbers CJ2-03, CJ2-04, CJ2-06, CJ2-09, CJ2-11, CJ2-12, CJ2-14, CJ2-16, CJ2-26, CJ2-29, CJ2-32, CJ2-37, and CJ2-38 have survived, although some in very rough condition. CJ2-06 and CJ2-09 have been restored.
CJ-2A
The lessons learned with the CJ-2 led to the development of the first full-production CJ, the 1945-1949 Willys-Overland CJ-2A, or Universal Jeep. A trademark for "AGRIJEEP" was granted in December 1944, but was not used. The CJ-2A looked very much like a civilianized MB with a tailgate and side-mounted spare wheel. A distinct difference between the MB and the CJ-2A lay in the grilles of the two vehicles. Where the MB had recessed headlights and nine-slot grilles, the CJ-2A had larger, slightly bulging headlights, flush-mounted in a seven-slot grille. While still powered by the reliable L-134 Go-Devil engine, the CJ-2A replaced the MB's T-84 transmission with a beefier T-90 three-speed.Production of the CJ-2A started on 17 July 1945, sharing production time with the MB roughly 9000 more MBs were produced through September 1945. Many of the early CJ-2As were produced using remaining stock of the military jeep components, such as engine blocks, and in a few cases, modified frames. Up to serial no. 13453, the MB-style full-floating rear axle was fitted. Once they were used up, the CJ got a stronger Dana / Spicer model 41. Sometimes the use of MB parts was due to strikes at suppliers, such as Autolite. Since Willys produced few parts in-house and relied heavily on suppliers, it was vulnerable to strikes. Unfortunately for Willys, strikes were common after the war, and this likely contributed to low production totals in 1945 and early 1946.
Since the CJ-2A was primarily intended for farming, ranching, and industrial applications, stock CJ-2As only came with a driver seat and driver side mirror, and a wide variety of options was available, such as: front passenger seat, rear seat, center rear-view mirror, canvas top, front power take-off, rear PTO, belt pulley drive, capstan winch, governor, rear hydraulic lift, snow plow, welder, generator, mower, disc, front bumper weight, heavy-duty springs, dual vacuum windshield wipers, dual taillights, hot-climate radiator, driveshaft guards, heater, side steps, and radiator brush guard.
The CJ-2As were produced in lively color combinations that in some ways symbolized the hope and promise of postwar America. True to their intended purpose, the combinations also resembled those used by the most popular farm equipment manufacturers of the day. From 1945 to mid-1946, CJ-2As were only available in two color combinations: Pasture Green with Autumn Yellow wheels and Harvest Tan with Sunset Red wheels. Additional color combinations added in mid-1946 were: Princeton Black with Harvard Red or Sunset Red wheels, Michigan Yellow with Pasture Green, Sunset Red or Americar Black wheels, Normandy Blue with Autumn Yellow or Sunset Red wheels, and Harvard Red with Autumn Yellow or Americar Black wheels. The Pasture Green and Harvest Tan combinations were dropped later in 1946. The Harvard Red combinations were dropped in 1947 and replaced with Picket Gray with Harvard Red wheels, and Luzon Red with Universal Beige wheels. In 1948, these color combinations were also added: Emerald Green with Universal Beige wheels, Potomac Gray with Harvard Red or American Black wheels. For 1949, the Picket Gray, Michigan Yellow, and Normandy Blue combinations were dropped. Olive drab was also available for export models.
On early CJ-2As, the front seats were covered in olive-drab vinyl. Around mid-1947, Slate Gray vinyl became available for certain color combinations. Later, Barcelona Red was added to the mix.
A total of 214,760 CJ-2As were produced. Because of the use of military production parts on the earliest CJ-2As, and the many changes made during their early production, restorers and collectors refer to CJ-2As up to around serial no. 34,530 as "Very Early Civilian" and from mid-1946 to about mid-1947 as "Early Civilian". Only minor changes were made after the mid-1947 models.
CJ-3A
The Willys-Overland CJ-3A was introduced in 1949, and was in production until 1953, when replaced by the CJ-3B. It was powered by Willys' L-134 Go-Devil four-cylinder engine, with a T-90 transmission and Dana 18 transfer case, a Dana 25 front axle, and Dana 41 or 44 rear axle. It featured a one-piece windshield with a vent and wipers at the bottom. The CJ-3A had beefed-up suspension to accommodate the various agricultural implements that were being built for the vehicle. Another difference was a shorter rear wheelwell and moving the driver's seat rearward. As of 1951, a Farm Jeep and a Jeep Tractor version were offered; the latter was very bare-bones, for field use only, and featured a power takeoff.In total, 131,843 CJ-3As were produced before the series ended in 1953. About 550 of the CJ3-As were assembled by Mitsubishi as the J1/J2 in late 1952 and early 1953, exclusively for the Japanese police and forestry agency.
The CJ-3A-derived military jeep was the Willys MC, and it began complementing the Ford and Willys World War II jeeps starting in 1949.
The CJ-3A, along with the later CJ-3B and CJ-5 models, was used as a platform for early Zamboni ice resurfacers produced from 1950 until 1964, which were mounted on top of the Jeeps to clean and smooth the surface of ice rinks. Zamboni resurfacers would be constructed using original chassis designs starting in 1964, eliminating the need to source Jeep parts.