Boiler (power generation)
A boiler or steam generator is a device used to create steam by applying heat energy to water. Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure but, at pressures above this, it is more usual to speak of a steam generator.
A boiler or steam generator is used wherever a source of steam is required. The form and size depends on the application: mobile steam engines such as steam locomotives, portable engines and steam-powered road vehicles typically use a smaller boiler that forms an integral part of the vehicle; stationary steam engines, heating plants, industrial installations and power stations will usually have a larger separate steam generating facility connected to the point-of-use by piping. A notable exception is the steam-powered fireless locomotive, where separately-generated steam is transferred to a receiver on the locomotive.
As a component of a prime mover
The steam generator or steam boiler is an integral component of a steam engine when considered as a prime mover. However it needs to be treated separately, as to some extent a variety of generator types can be combined with a variety of engine units. A boiler incorporates a firebox or furnace in order to burn the fuel and generate heat. The generated heat is transferred to water to make steam, the process of boiling. This produces saturated steam at a rate which can vary according to the pressure above the boiling water. The higher the furnace temperature, the faster the steam production. The saturated steam thus produced can then either be used immediately to produce power via a turbine and alternator, or else may be further superheated to a higher temperature; this notably reduces suspended water content making a given volume of steam produce more work and creates a greater temperature gradient, which helps reduce the potential to form condensation. Any remaining heat in the combustion gases can then either be evacuated or made to pass through an economiser, the role of which is to warm the feed water before it reaches the boiler.Types
Haycock and wagon top boilers
For the first Newcomen engine of 1712, the boiler was little more than large brewer's kettle installed beneath the power cylinder. Because the engine's power was derived from the vacuum produced by condensation of the steam, the requirement was for large volumes of steam at very low pressure hardly more than. The whole boiler was set into brickwork which retained some heat. A voluminous coal fire was lit on a grate beneath the slightly dished pan which gave a very small heating surface; there was therefore a great deal of heat wasted up the chimney. In later models, notably by John Smeaton, heating surface was considerably increased by making the gases heat the boiler sides, passing through a flue. Smeaton further lengthened the path of the gases by means of a spiral labyrinth flue beneath the boiler. These under-fired boilers were used in various forms throughout the 18th century. Some were of round section. A longer version on a rectangular plan was developed around 1775 by Boulton and Watt. This is what is today known as a three-pass boiler, the fire heating the underside, the gases then passing through a central square-section tubular flue and finally around the boiler sides.Cylindrical fire-tube boilers
An early proponent of the cylindrical form was the British engineer John Blakey, who proposed his design in 1774. Another early proponent was the American engineer, Oliver Evans, who rightly recognised that the cylindrical form was the best from the point of view of mechanical resistance and towards the end of the 18th century began to incorporate it into his projects. Probably inspired by the writings on Leupold's "high-pressure" engine scheme that appeared in encyclopaedic works from 1725, Evans favoured "strong steam" i.e. non-condensing engines in which the steam pressure alone drove the piston and was then exhausted to atmosphere. The advantage of strong steam as he saw it was that more work could be done by smaller volumes of steam; this enabled all the components to be reduced in size and engines could be adapted to transport and small installations. To this end he developed a long cylindrical wrought iron horizontal boiler into which was incorporated a single fire tube, at one end of which was placed the fire grate. The gas flow was then reversed into a passage or flue beneath the boiler barrel, then divided to return through side flues to join again at the chimney. Evans incorporated his cylindrical boiler into several engines, both stationary and mobile. Due to space and weight considerations the latter were one-pass exhausting directly from fire tube to chimney.Another proponent of "strong steam" at that time was the Cornishman Richard Trevithick. His boilers worked at and were at first of hemispherical then cylindrical form. From 1804 onwards Trevithick produced a small two-pass or return flue boiler for semi-portable and locomotive engines. The Cornish boiler developed around 1812 by Richard Trevithick was both stronger and more efficient than the simple boilers which preceded it. It consisted of a cylindrical water tank around long and in diameter, and had a coal fire grate placed at one end of a single cylindrical tube about three feet wide which passed longitudinally inside the tank. The fire was tended from one end and the hot gases from it travelled along the tube and out of the other end, to be circulated back along flues running along the outside then a third time beneath the boiler barrel before being expelled into a chimney. This was later improved upon by another 3-pass boiler, the Lancashire boiler which had a pair of furnaces in separate tubes side-by-side. This was an important improvement since each furnace could be stoked at different times, allowing one to be cleaned while the other was operating.
Railway locomotive boilers were usually of the 1-pass type, although in early days 2-pass return-flue boilers were common, especially with locomotives built by Timothy Hackworth.
Multi-tube boilers
A significant step forward came in France in 1828 when Marc Seguin devised a two-pass boiler of which the second pass was formed by a bundle of multiple tubes. A similar design with natural induction used for marine purposes was the popular Scotch marine boiler.Prior to the Rainhill trials of 1829 Henry Booth, treasurer of the Liverpool and Manchester Railway suggested to George Stephenson, a scheme for a multi-tube one-pass horizontal boiler made up of two units: a firebox surrounded by water spaces and a boiler barrel consisting of two telescopic rings inside which were mounted 25 copper tubes; the tube bundle occupied much of the water space in the barrel and vastly improved heat transfer. Old George immediately communicated the scheme to his son Robert and this was the boiler used on Stephenson's Rocket, outright winner of the trial. The design formed the basis for all subsequent Stephensonian-built locomotives, being immediately taken up by other constructors; this pattern of fire-tube boiler has been built ever since.
Structural resistance
The 1712 boiler was assembled from riveted copper plates with a domed top made of lead in the first examples. Later boilers were made of small wrought iron plates riveted together. The problem was producing big enough plates, so that even pressures of around were not absolutely safe, nor was the cast iron hemispherical boiler initially used by Richard Trevithick. This construction with small plates persisted until the 1820s, when larger plates became feasible and could be rolled into a cylindrical form with just one butt-jointed seam reinforced by a gusset; Timothy Hackworth's Sans Pareil 11 of 1849 had a longitudinal welded seam. Welded construction for locomotive boilers was extremely slow to take hold.Once-through monotubular water tube boilers as used by Doble, Lamont and Pritchard are capable of withstanding considerable pressure and of releasing it without danger of explosion.
Combustion
The source of heat for a boiler is combustion of any of several fuels, such as wood, coal, oil, or natural gas. Nuclear fission is also used as a heat source for generating steam. Heat recovery steam generators use the heat rejected from other processes such as gas turbines.Solid fuel firing
In order to create optimum burning characteristics of the fire, air needs to be supplied both through the grate, and above the fire. Most boilers now depend on mechanical draft equipment rather than natural draught. This is because natural draught is subject to outside air conditions and temperature of flue gases leaving the furnace, as well as chimney height. All these factors make effective draught hard to attain and therefore make mechanical draught equipment much more economical. There are three types of mechanical draught:- Induced draught: This is obtained one of three ways, the first being the "stack effect" of a heated chimney, in which the flue gas is less dense than the ambient air surrounding the boiler. The denser column of ambient air forces combustion air into and through the boiler. The second method is through use of a steam jet. The steam jet or ejector oriented in the direction of flue gas flow induces flue gases into the stack and allows for a greater flue gas velocity increasing the overall draught in the furnace. This method was common on steam driven locomotives which could not have tall chimneys. The third method is by simply using an induced draught fan which sucks flue gases out of the furnace and up the stack. Almost all induced draught furnaces have a negative pressure.
- Forced draught: draught is obtained by forcing air into the furnace by means of a fan and duct-work. Air is often passed through an air heater; which, as the name suggests, heats the air going into the furnace in order to increase the overall efficiency of the boiler. Dampers are used to control the quantity of air admitted to the furnace. Forced draught furnaces usually have a positive pressure.
- Balanced draught: Balanced draught is obtained through use of both induced and forced draft. This is more common with larger boilers where the flue gases have to travel a long distance through many boiler passes. The induced draft fan works in conjunction with the forced draft fan allowing the furnace pressure to be maintained slightly below atmospheric.