Mack MC/MR series
The Mack MC/MR series, also known as the "Cruise-Hauler", is a cabover truck first introduced in 1978. It is of a distinct "set back front axle" design, with the driver compartment mounted ahead of the front axle and with a large, flat, divided windscreen covering almost half of the truck's frontal aspect.
The MC was used for custom-built fire equipment, when Mack exited the market in 1990 they discontinued the MC. The MR was widely used in refuse applications and continued in production until up-graded as the MRU TerraPro in 2007.
Design
The MC/MR was designed from the beginning to be available in right-hand drive as well as left-hand drive. This allowed Mack to market the truck in the United Kingdom without costly conversions, and also opened the trash truck market at home. The right-hand drive models also have the exhaust relocated to the left, while the turbocharger is mounted behind the engine so as to provide more space and less heat soak. Export models are coded MCE and MRE respectively. The low profile cab is of steel, while the doors are fibreglass. The engine intrudes considerably into the low cab. The cab tilts through a full 90 degrees, allowing for the radiator to be removed without first removing the cab. The dashboard is lit from a single source through fibreoptics, this being a very early example of such an application.Engines
The MC was available with Mack E6 series and mid-range Caterpillar 3208 series diesel engines. The MR was available with the E6 series and E7 series diesel engines.Maxidyne high-torque engines have a wide power band and can develop maximum power below the governed speed they are rated at. This allows less shifting and smoother power "on the ground" when accelerating. Most MR series had Maxidyne engines.
The Mack E6 was a turbocharged inline six-cylinder engine. it developed.
The Mack E7 was a turbocharged inline six-cylinder engine. It 1998 it developed and of torque.
The Caterpillar 3208 was a V8 engine. It developed and of torque.
Transmissions
Mack, Allison, Fuller, and Spicer transmissions have been available, evolving over time. Each was suited for different applications.All manual transmission except the 6-speed had a 5-speed transmission, additional speeds were made with combinations of ranges. The lowest transmission gear can be either an on-road or very low off-road ratio.
Mack Maxitorque transmissions are designed to work with Maxidyne engines and have fewer and wider-spaced gears than more conventional models. They originally had 5 speeds and developed into 8 speeds with low range gears. Other Mack manual transmissions have 5-10 speeds.
Allison automatic transmissions are widely used on refuse trucks. Early models had 4 or 5 speeds and evolved with 5 or 6 speeds. They are fully automatic planetary gear transmissions and later models have lock-up torque converters.
Fuller Roadranger transmissions are multi-range and suited for non-Maxidyne engines, which need more speeds. They had 10 highway speeds and an optional low range.
Spicer 5-speed transmissions were available in 400 series trucks.
Transfer cases are used on concrete pumps. They direct full transmission output to either the drive-line or the pump, but not both at the same time.
Axles and suspensions
Front axles were rated at in light MC models but most models had between. Steering could have up to a 45 cut, allowing very tight turning radius.Single rear axles rated at were used in small MC models, but most were and later MR models could be up to.
The Camelback tandem is the base rear suspension. The Camelback has multiple leaves that rock above the bogey pivot then curve down and under the axles. It is strong in on/off-road service. It is available in ratings of.
Walking beams have low bogie pivots with a balance beam going out and under the axles. Any suspension is above the bogey pivot. They can have leaf springs or be solidly mounted. Walking beams are very stable at low speeds and when stopped.
Applications
Refuse
Front loaders drive directly up to a container. A boom goes from the body over and then down in front of, the cab. As the truck moves forward slowly two forks pick up the container. The container is then lifted up and over the cab to be dumped into a hopper on the top of the body. Front loaders are used for commercial pickup.Rear loaders have a large hopper on the rear end. Typically a rear crew can load loose material, bins with assist, oversize pieces, and small containers. They are used for residential and light commercial pickup in congested cities.
Roll-off container trucks have a container that is raised in the front and slides off the back of the truck onto the ground. When a loaded box is carried it can be unloaded like a dump truck. They commonly haul construction debris but refuse containers are also left at commercial sites. MC/MRs are sometimes used in congested cities when extreme maneuverability is required.
Construction
Concrete pumps have a multi-stage folding boom pivoted near the center of the truck and a hopper at the rear to load the pump. The pump itself is the load and the truck always operates at maximum weight. In transit the boom is folded front to rear. In use the pump uses outriggers and the boom unfolds forward over the cab or to either side. Large pumps can have multiple extra axles.Concrete conveyors have a telescopic conveyor belt. They do similar work to a pump but are limited and rarely as heavy as a pump.
Roll-off container trucks have a container that is raised in the front and slides off the back of the truck onto the ground. When a loaded box is carried it can be unloaded like a dump truck. They commonly haul construction debris but refuse and garbage containers are also left at commercial sites.