Hydrogen purification
Hydrogen purification is any technology used to purify hydrogen. The impurities in hydrogen gas depend on the source of the H2, e.g., petroleum, coal, electrolysis, etc. The required purity is determined by the application of the hydrogen gas. For example, ultra-high purified hydrogen is needed for applications like proton exchange membrane fuel cells.
Purification technologies
Low temperature methods
The default large-scale purification of H2 produced in oil refineries exploits its very low boiling point of −253 °C. Most impurities have boiling points well above this temperature. Low temperature methods can be complemented by scrubbing to remove particular impurities.Palladium membrane hydrogen purifiers
Hydrogen can be purified by passing through a membrane composed of palladium and silver. Permeability of the former to hydrogen was discovered back in the 1860s. An alloy with a ca. 3:1 ratio for Pd:Ag is more structural robust than pure Pd, which is the active component that allows the selective diffusion of H2 through it. Diffusion is faster near 300 °C. This method has been used for purification of hydrogen on a laboratory scale, but not in industry. Silver-palladium membranes are unstable toward alkenes and sulfur-containing compounds.Dense thin-metal membrane purifiers are compact, relatively inexpensive and simple to use.
Pressure swing adsorption
Pressure swing adsorption is used for the removal of carbon dioxide as the final step in the large-scale commercial synthesis of hydrogen. It can also remove methane, carbon monoxide, nitrogen, moisture and in some cases, argon, from hydrogen.Applications
Metalorganic vapour phase epitaxy
Hydrogen purifiers are used in metalorganic vapour phase epitaxy reactors for LED production.PEM fuel cells
Fuel cell electric vehicles commonly use polymer electrolyte membrane fuel cells that are susceptible to a range of impurities. Impurities impact PEMFC using a range of mechanisms, these may include poisoning the anode hydrogen oxidation reaction catalysts, reducing the ionic conductivity of the ionomer and membrane, altering wetting behaviour of components or blocking porosity in diffusion media. The impact of some impurities like carbon monoxide, formic acid, or formaldehyde is reversible with PEMFC performance recovering once the supply of impurity is removed. Other impurities, for example sulphurous compounds, may cause irreversible degradation. The permissible limits of hydrogen impurities are shown below.| Maximum Permissible Concentration / μmol mol−1 | |
| Total non-hydrogen gasses | 300 |
| Water | 5 |
| Total Hydrocarbons Except Methane | 2 |
| Methane | 100 |
| Oxygen | 5 |
| Helium | 300 |
| Nitrogen | 300 |
| Argon | 300 |
| Carbon Dioxide | 2 |
| Carbon Monoxide | 0.2 |
| Total Sulphur Compounds | 0.004 |
| Formaldehyde | 0.2 |
| Formic Acid | 0.2 |
| Ammonia | 0.1 |
| Halogenated Compounds | 0.05 |
| Maximum Particulate Concentration | 1 mg kg−1 |
Efforts to assess the compliance of hydrogen supplied by hydrogen refuelling stations against the ISO-14687 standard have been performed. While the hydrogen was generally found to be 'good' violations of the standard have been reported, most frequently for nitrogen, water and oxygen.
Combustion engines and appliances
Combustion applications are generally more tolerant of hydrogen impurities than PEFMC, as such the ISO-14687 standard for permissible impurities is less strict. This standard has itself been criticised with revisions proposed to make it more lenient and therefore suitable for hydrogen distributed through a repurposed gas network.| Impurity | Maximum Permissible Concentration / μmol mol−1 |
| Total non-hydrogen gasses | 20 000 |
| Water | Non-condensing |
| Total Hydrocarbons | 100 |
| Carbon Monoxide | 1 |
| Sulphur | 2 |
| Combined water, oxygen, nitrogen, argon | 19 000 |
| Permanent Particulates | Shall not contain an amount sufficient to cause damage. |
Methods for analysis
As the permissible concentrations for many impurities are very low this sets stringent demands on the sensitivity of the analytical methods. Moreover, the high reactivity of some impurities requires use of a properly passivated sampling and analytical systems. Sampling of hydrogen of is challenging and care must be taken to ensure that impurities are not introduced to the sample and that impurities do not absorb on or react within the sampling equipment, there are currently different methods for sampling but rely on filling a gas cylinder from the refuelling nozzle of a refuelling station. Efforts are underway to standardise and compare sampling strategies. A combination of different instruments is needed to assess hydrogen samples for all of the components listed in ISO 14687-2. Techniques suitable for individual impurities are indicated in the table below.| Impurity | Possible Analytical Methods | Detection Limits |
| Total non-hydrogen gasses | ||
| Water | Quartz crystal microbalance or CRDS | 1.3 or 0.030 |
| Total Hydrocarbons Except Methane | GC-Methaniser-FID | 0.1 |
| Methane | GC-Methaniser-FID, GC-EPD | 0.1 |
| Oxygen | GC-PDHID, GC-EPD | 0.3 |
| Helium | GC-TCD | 10 |
| Nitrogen | GC-PDHID, GC-EPD | 1 |
| Argon | GC-PDHID, GC-EPD | 0.3 |
| Carbon Dioxide | GC-Methaniser-FID, GC-EPD | 0.02 |
| Carbon Monoxide | GC-Methaniser-FID, GC-EPD | 0.02 |
| Total Sulphur Compounds | GC-SCD, GC-EPD | 0.001 |
| Formaldehyde | GC-Methaniser-FID | 0.1 |
| Formic Acid | FTIR | 0.2 |
| Ammonia | GC-MS or UV-visible spectroscopy or FTIR | 1 or 0.03 or 0.1 |
| Halogenated Compounds | TD-GC-MS | 0.016 |
Techniques such as electrochemical sensors and mass spectrometry.