Fiat Fiasa engine


Designed by Aurelio Lampredi, the Fiasa engine first appeared in the Brazilian-built Fiat 147 in September 1976, and shortly afterwards in the 'Series 2' version of the Fiat 127. The name Fiasa is a portmanteau of "Fiat Automóveis S.A.", for whom it was developed. The in-line four-cylinder engine has five main bearings, a cast iron block with an aluminium cylinder-head with belt-driven overhead camshafts actuating the valves. The engine remained in production until 2001 in Latin America, and also provided the basis for a diesel version. The capacity was initially, but Lampredi designed the engine to be suited for a considerably longer stroke. Sizes eventually ranged between. The last versions of this engine to be built was a 1.5-litre, dedicated-ethanol version developed in Brazil that served the Fiat Uno and its derivatives, and later yet the Fiat Palio until 2001.

Engine specifications

The Fiasa engine was produced in a number of stroke lengths but always of nearly the same bore. The first model was very oversquare, using a bore and a stroke of to produce a displacement of 1049 cc. The rod length was an ample, meaning that much larger strokes were possible without any negative consequences. The engine was designed to provide good low-down torque and fuel economy, but not for high peak power, and the compression ratio was a very low 7.2:1 to deal with the low octane petrol commonly available in Brazil at the time. It had a single-barrel carburetor and the intake manifolds were narrow, restricting peak power while providing good performance at lower engine speeds. It had breakerless electronic ignition and chrome-treated exhaust valves with stellite seats, for increased durability. A larger version arrived in 1979, again tuned for low down torque. This has a stroke. This larger engine was also available in a sportier version with twin-barrel Webers and more power. A third version of the 1.3 was Fiat's and the world's first modern ethanol-powered engine. As exports to Europe commenced, the 1.3 was later bored out by 0.1 mm, to nudge the displacement above 1.3 liters. This allowed Italian motorists to drive a full on the autostrada, rather than the to which cars under 1.3 litres were limited. The diesel derivative was also of this dimension.
The Brazilian engines were also exported to Europe in large numbers, both for the 127, Ritmo, and the later Uno. The fully finished engines were shipped in large containers containing 144 engines each. The 1.05 was also installed in the Autobianchi Y10, where it was also available with turbocharging.
Fiat later made a very short-lived derivative, using a stroke. This was only installed in the sporty Fiat Oggi CSS, which was built in 300 examples in 1984. This engine produces. The next version was an undersquare version with a much longer stroke, the version with a which was introduced for the Fiat Fiorino in 1989. The little 1050 was discontinued in 1989 as well. The final iteration was developed to fit Brazil's new sub-1 liter tax category and was introduced in 1990. Displacing, it had an extremely short stroke of. With a single carburetor, the new engine's specifications were very similar to the 1.05. A higher-powered, twin-barrel ethanol-powered version was introduced in 1991 for the Uno Brio but was discontinued shortly thereafter as it could not meet the new emissions regulations which took effect in January 1992. With these, only the single-barrel 1.0 and the 1.5 remained available.
The catalyzed 1.0 was not cost effective, and for 1993 Fiat switched to an electronically controlled, double-barrel Weber 495 carburetor and was able to forego the catalyst. The new "Mille Electronic" cost less to build and power was higher than before the new emissions impositions. However, the production cars appear not to have met the 1992 standards and in November 1995 Fiat was fined R$ 3.93 million for the 429,928 non-conforming Mille Electronic/ELX sold between December 1992 to June 1995.
Some engine capacities are equal to those of the Fiat OHC engines, OHV engines and DOHC engines built in Italy, but these are not the same engines.

Applications

List of vehicles using variations of the Fiasa engine :
;Petrol engine
  • Fiat 147/Spazio: 1976–1987
  • Fiat 127 Series 2/3: 1977-1987
  • Fiat Fiorino: 1979-2000
  • Fiat Panorama: 1980–1986
  • Fiat Oggi: 1983–1985
  • Fiat Uno/Mille: 1984-2001
  • Fiat Prêmio/Duna/Elba: 1985–1999
  • Fiat Ritmo/Strada: 1978-1988
  • Innocenti Mille: 1994–1997
  • Fiat Palio: 1996–2001
  • Autobianchi/Lancia Y10: 1985–1995
;Diesel engine
  • Fiat 127: 1981-1987
  • Fiat 147/148/Spazio: 1981–1990
  • Fiat Panorama
  • Fiat Uno: 1983-1989
  • Fiat Panda: 1986-1989
  • Fiat Fiorino: 1981-1987
  • Fiat Duna: 1987-1991