Electrofusion welding
Electrofusion welding is a form of resistive implant welding used to join pipes. A fitting with implanted metal coils is placed around two ends of pipes to be joined, and current is passed through the coils. Resistive heating of the coils melts small amounts of the pipe and fitting, and upon solidification, a joint is formed. It is most commonly used to join polyethylene and polypropylene pipes. Electrofusion welding is the most common welding technique for joining PE pipes. Because of the consistency of the electrofusion welding process in creating strong joints, it is commonly employed for the construction and repair of gas-carrying pipelines. The development of the joint strength is affected by several process parameters, and a consistent joining procedure is necessary for the creation of strong joints.
Advantages and disadvantages
Advantages of electrofusion welding:- Simple process capable of producing consistent joints
- Process is entirely contained, reducing the risk of joint contamination
- Process allows repair without the need to remove pipes
- A special sleeve is required, so it is more expensive than other pipe joining methods such as hot plate joining
- Implanted coils make recycling of parts more difficult
Equipment
Electrofusion welds are performed by attaching a controlled power supply to the electrofusion fitting. There are typically two modes of operation.Constant voltage is typically used for high pressure pipelines such as mains gas and water. Fittings are fitted with a barcode specified to an ISO standard.
Typically fittings will be welded at 39.5v, but manufacturers can choose voltages in whole numbers from 8 to 48v. The welding time is specified on the label in seconds or minutes
Accessories
Electrofusion welding employs fittings that are placed around the joint to be welded. Metal coils are implanted into the fittings, and electric current is run through the coils to generate heat and melt part of the pipes, forming a joint upon solidification. There are two possible fittings used in electrofusion welding: couplers and tapping tees. Coupler fittings contain two separate regions of coils, creating two distinct fusion zones during welding. The inner diameter of the coupler is typically slightly larger than the outer diameter of the pipes. This is to increase the ease of assembly in the field and allows for minor inconsistencies in pipe diameter. Proper insertion of the pipes in the coupler is critical for the creation of a strong joint. Incorrect placement of the coupler can cause the coils to move and lead to the extrusion of molten polymer material from the joint, reducing the joint's strength. Tapping tees, or saddles, are less common but operate under the same principles as a coupler. They require clamping to ensure a proper fit up with the pipes.Fitting installation
Installation of couplers and tapping tee fittings require slightly different procedures. Common installation steps for each are given below.Couplers
- Wash pipe ends to create clean surfaces for joining
- Square pipe ends to facilitate optimal fit-up
- Clean area where coupler will be placed with isopropyl alcohol
- Mark the pipes slightly beyond half the length of the coupler, to indicate where scraping will take place in later steps
- Mark the area to be scraped
- Scrape pipe in marked areas to remove surface layer, allowing clean pipe material to contact the coupler
- Examine scraped area thoroughly, making sure that fresh pipe material is exposed throughout area
- Insert pipe ends into coupling to appropriate depth
- Secure coupler using clamp
- Connect fitting to control box using electrical leads
- Apply fusion cycle
- Allow joint to be undisturbed for the entire prescribed cooling time
- Pressure test pipe
- Back fill pipe with appropriate contents
- Begin service
Tapping tee
- Wash pipe area to be joined to create clean surfaces for joining
- Clean area where tapping tee will be placed with isopropyl alcohol
- Mark the pipes slightly beyond the edges of the tapping tee location
- Scrape pipe in marked areas to remove surface layer, allowing clean pipe material to contact the tapping tee
- Examine scraped area thoroughly, making sure that fresh pipe material is exposed throughout area
- Place tapping tee onto joint
- Secure tapping tee using clamp
- Connect fitting control box using electrical leads
- Apply fusion cycle
- Allow joint to be undisturbed for the entire prescribed cooling time
- Pressure test pipe
- Back fill pipe with appropriate contents
- Begin service
Power requirements
Electrofusion welding requires electrical current to be passed through the coils implanted in the fittings. Since the electrical energy input is an excellent indicator of the joint strength that develops during fusion, it is necessary to have consistent electrical power input. Energy input during the joining process is typically measured by controlling the time it takes for the current to pass through the fitting. However, energy input can also be monitored by controlling overall temperature, molten polymer temperature, or molten polymer pressure.A control box takes electrical power from a generator and converts it into an appropriate voltage and current for electrofusion joining. This provides consistent energy input for each application. The most common input voltage for electrofusion welding fittings is 39.5V, as it provides the best results without risking operator safety. The current is input as an alternating current waveform.
Welding process
Stages during welding
Electrofusion welding is characterized by four distinct stages that occur during the welding process:- Incubation period
- Joint formation and consolidation
- Plateau region
- Cooling period
Current during welding
Most electrofusion welding power supplies are constant voltage machines. Constant current machines would provide more consistent energy input due to the smaller fluctuations in current applied to the coils during welding. However, this additional consistency is generally not worth the higher cost of these machines. When a constant voltage machine is used, the value of the applied current slowly decreases throughout the welding process. This effect is due to the increasing resistance of the coils as energy is applied. As heat is generated in the coils, their temperature increases, leading to a higher electrical resistance in the coils. This increased electrical resistance causes a smaller current to be generated from the same voltage level as the process progresses. The extent of the current decrease is determined by the material used for the coil. The energy input per unit area can be calculated and used to monitor the process. Typical values for this range from 2–13 J/mm2, with a value of 3.9 J/mm2 having been found to produce the strongest joints.Temperature during welding
Large temperature gradients exist in the electrofusion joint during the fusion cycle. The low thermal conductivity of polymers is the main cause of these large gradients. Recent efforts to model the thermal history at various locations using finite element modeling have been successful.Pressure during welding
As the temperature in the joint increases, polymer begins to melt and a fusion zone is formed. The molten polymer in the fusion zone exerts an outward force on the surrounding solid polymer material, referred to as "cold zones". These cold zones cause a pressure to develop in the molten fusion zone. The pressure in the fusion zone takes some time to reach its maximum value, usually not reaching the peak until about a quarter of the way into the joining process. After the current is shut off and cooling begins, the pressure slowly decreases until the joint is uniform temperature.Properties of joints
The strength of an electrofusion joint is measured using tensile and peel tests on coupons taken from the fusion zone of the joint. Two methods have been developed to assess the effect of fusion time on joint strength:- Simulating an electrofusion joint solely for testing purposes
- Removing test coupons from standard electrofusion welded joints