Dodge WC series


The Dodge WC series, nicknamed "Beeps", and at first is a prolific range of light 4WD and medium 6WD military utility trucks, produced by Chrysler under the Dodge and Fargo marques during World . Together with the later ton jeeps produced by Willys and Ford, the Dodge ton and ton trucks made up nearly all of the [Military light utility vehicle|light 4WD trucks] supplied to the U.S. military in WW II – with Dodge contributing some 337,500 4WD units.
Contrary to the versatility of the highly standardized ton jeeps, which was mostly achieved through field modification, the Dodge WCseries came in many different, purpose-built, but mechanically uniform variants from the factory, much akin to the later family of High Mobility Multipurpose Wheeled Vehicles. The WC series evolved out of, and was part of a more extended family of trucks, with great mechanical parts commonality, that included open- and closed-cab cargo, troops and weapons carriers, command, and reconnaissance cars, ambulances, carry-alls, panel vans, and mobile telephone installation and field workshop trucks.
The Dodge WC series were essentially built in two generations. From 1940 to early 1942, almost 82,400 of the ton 4x4 Dodge trucks were built. Initially called the VC series, these were the U.S. military's first ever "light" four-wheel drive, -production trucks, preceding the momentous 1940 rethink, leading to the creation of the "-ton truck". However, the great majority, from the 1941 model year, were named WC series, and built in more variants. Contrary to what Dodge's nomenclature maybe suggested, the 1941 WC models were a straight evolution of the 1940 VC models, retaining their U.S. Army Ordnance Corps' Supply Catalog number.
For 1942, the trucks bodies and chassis were largely redesigned – heavier frames and drivetrains uprated them to carry tons off-road. And widening their tracks, while greatly shortening the wheelbase on the main models, plus lowering the bodies' center of gravity, gave them a much more square stance, with a much better break-over angle and side-slope stability. The trucks thus became the shorter [List of U.S. military vehicles by supply catalog designation#G500 to G599|], ton, 4×4 truck , and from 1943 also the longer, stretched [List of U.S. military vehicles by supply catalog designation#G500 to G599|], 1ton, 6x6 personnel and cargo truck — all while retaining Dodge WC model codes. Although the tons improvements meant substantial design changes, they did retain some 80% interchangeable components and service parts with the ton models — a vital Army requirement, for field maintenance and operability of the trucks.
Dodge was the U.S. Army's main supplier of ton trucks, and its sole supplier of both ton trucks and 1ton 6x6 trucks in World War II. With over a quarter million units built through August 1945, the tons were the most common variants in the WCseries.

After the war, Dodge developed the -ton WCseries into the civilian 4×4 Dodge Power Wagon; and in 1951, the WCs were replaced by the very similar ton 4x4 Dodge M-series vehicles.
Though the majority of Dodges built were 'Weapons Carriers', "WC" was not abbreviated from this, but a regular Dodge model code – initially "W" for 1941, and "C" for a nominal half-ton payload rating. However, the "WC" model code was simply retained after 1941 — for both the, as well as the rated 6x6 Dodges.
All in all, not counting mechanically related variants, the WC series alone involved 52 model versions. Creating vehicles of a common platform in such a variety of designs, with payloads ranging from ton to 1tons, had no equal in its time, and is seen as an extraordinary feat of the WWII American auto industry.

Scope of the Dodge WC series

The name of this article would at first suggest a focus on models that are indeed called Dodge WC-numbers, either 4x4 or 6x6. However, the U.S. Army Ordnance Corps' central Standard Nomenclature List (SNL) Supply Catalog, covering the WC series, conveys both by its title, "SNL G-657 – Master Parts List, Dodge Trucks", as well as by, that, the family of vehicles must at least be considered to include the:
  • 1940 half-ton VC series and -ton VF models
  • 1941 half-ton WC series
  • 1942 three-quarter ton and 1943 -ton WC series, but also
  • 1941 two-wheel drive half-tons and -ton WC series.
Additionally, close variants of the T-207 WC-1, and of the T-214 WC-51/WC-52, were derived and made in Canada, as the T212 'D8A' and the T236 '3/4 Ton APT' respectively; and further production of T-203 variants became indicated as both the T-203B, and as the WF series.
By contrast, Chrysler / Dodge Canada built another 165,000 mostly three-ton trucks, a hasty addition to the production of Canadian Military Pattern trucks, that were more closely derived from the commercial Dodge T-, V-, and W-Series trucks, and the same is true for the 15,000 'parts bin special' (T-234) "Burma Road" trucks, ordered by Chinese leader Chiang Kai-shek, at the time an ally against Japan.

History and design

1900–1939 — Dodge Brothers start making cars and 4x4 trucks for the U.S. Army

Dodge had been the United States military's primary supplier of light wheeled vehicles, since before the U.S. joined the First World War. After starting business in 1900, producing precision engine and chassis components for other car builders in Detroit — Ford and Oldsmobile chief among these — Dodge introduced their first car, the Model 30/35 tourer, in 1914. It was stronger and more high quality than the ubiquitous Ford , and in 1916, Dodge cars immediately proved their durability, both in the 1910s U.S.–Mexico Border War — the U.S. military's first operation to use truck convoys, as well as in World War I, when some 12,800 Dodge cars and light trucks were used, primarily as ambulances and repair trucks., but also as staff and reconnaissance vehicles. All the while, Dodge maintained its reputation for high quality truck, transmission, and motor parts they kept making for other successful manufacturers.
Dodge civilian, commercial trucks were at first largely based on their passenger cars, offering light- and medium-duty trucks, like pickups, station hacks, panel vans, and carry-alls. Dodge's passenger-car chassis were sturdy enough for such trucks, from their 1914 introduction. But Dodge expanded into medium-heavy duty trucks during the later 1930s and the 1940s. Crucial developments for Dodge were the switch to specific truck-frames and bodies in 1935, for a new, 1936 model-year truck generation. The dedicated truck frames were heavier and stronger than the lighter passenger-car chassis. In 1938, Dodge opened a very large new factory, dedicated to truck manufacturing, and later that same year, Dodge introduced a drastically redesigned new truck line-up again: the 1939 T-series 'Job-rated' trucks.
Dodge developed their first four-wheel drive truck in 1934, requested by the U.S. Army — an experimental 1 ton rated model, designated K-39-X-4, of which 796 units were ordered, in multiple configurations. Timken supplied driven front axles and transfer-cases, which were added to a militarized commercial truck. The Timken transfer case was the first part-time design, that allowed the driver to engage or disengage four-wheel drive using a lever inside the cabin. In spite of the limited 1930s U.S. military budgets, the 1934 trucks served well enough that, after a couple of years, Dodge received further Army contracts for 1ton, 4-wheel drive trucks, and these were further developed from the late thirties. Dodge built the U.S. Army further batches of 1ton 4x4 trucks in 1938, 1939 and 1940.
In 1938, a batch of 1,700 experimental RF-40-X-4 trucks were procured, and a further 292 experimental units, typed TF-40-X-4 in 1939 – the first to be built, based on Dodge's new for 1939 T-, V-, and W-Series trucks. All of the 1-ton Army 4x4s, including the 800 trucks of 1934, rode on a wheelbase, and the 1938 RF-40 and 1939 TF-40 four-wheel drives were the first for which Dodge moved to separate engineering codes, in the T-200 range.
However, Dodge also eagerly pursued military contracts for half-ton four-by-fours at the same time. The smaller size had outperformed the 1-ton 4x4 during testing in 1938, and Dodge had invested greatly in half- to one-ton trucks in prior years. In 1936, Dodge's light, car-based trucks had been crucially redesigned — abandoning the use of passenger car frames, instead for the first time built on distinct, modern truck-style chassis, with the frame-rails welded to the cross-members on their half-ton to one-ton rated trucks. Additionally, Dodge had built their all new, very large Warren Truck Assembly plant in Michigan, specifically for mass-production of light and medium trucks, opened in 1938.
Then, for the 1939 model year, Dodge again presented a completely redesigned line of pickups and trucks – the art-deco styled, Dodge T-, V-, and W-Series "Job-Rated" trucks, available in an unprecedented number of sizes, payload rates and configurations, aiming the trucks to fit every different job.

1940 — -ton VC and 1-ton VF models

Well before the onset of World War II, it was clear that the USA needed to update its military. The Quartermaster Corps, responsible at the time for providing the military with non-combat vehicles, moved to standardize truck designs, and by 1939, as the war in Europe erupted, the Army had settled on five payload-based general-purpose, cross-country truck classes:,, -, 4- and. Introduction of a ton standard 4WD class meant a significant doctrine shift, away from the conventional belief that all the extra weight, costs and mechanical complexity of adding 4-wheel-drive wouldn't be worth it on any general purpose military vehicle with an off-highway payload capacity, below the standard 1ton Army cargo unit. Mirroring the civilian market, where the use of all-wheel drive was practically non-existent in anything below payload vehicles. Light-duty off-roaders were a very small niche-market, only filled by after-market conversions, primarily by Marmon-Herrington.
By June 1940 the Q.C. had tested and approved its first three standard commercial based, all-wheel drive trucks: the 4x4 Dodge, the GMC 6x6 and a Mack 6x6. With regards to Dodge however, the U.S. military reconsidered its preferences for the build-up for the war almost immediately after this.
Although in 1936, a Marmon-Herrington converted half-ton Ford had become the Army's first light 4-wheel drive, and the Army had initially standardized Dodge's 4x4 trucks in the class — following Dodge's push for building tons, after mid 1940 the Army decided they preferred Dodge to build the light-duty four-wheel drives, contracting for a series of half-ton trucks, while GM / Chevrolet was instead going to become the standard supplier for trucks. Dodge successfully outbid GMC's 1939 ACK-101 half-ton truck, as well as Marmon-Herrington, who could not retrofit in the required volume or price, not to mention International's M-1-4 half-ton truck, which wasn't built until 1941, for the U.S. Marine Corps. So, when in the summer of 1940 the largest government truck contract awarded went to Chrysler's Dodge / Fargo Division, for more than 14,000 4x4 trucks, this was in the midst of the transition, and thus included both orders for ton and 1ton trucks, as GM / Chevy still needed to tool up for mass-producing 4WD 1-tonners.
Dodge had started developing designs for a 4x4 half-ton in 1939, and began production in earnest in 1940 — both 4x4 half-tons, as well as 1-ton 4x4 and 4x2 trucks. On all 1940 trucks, front sheetmetal was mostly identical to the commercial VC and VF models of that year, with the addition of a big brush guard mounted in front of the grille and headlights. Except for the addition of 4-wheel drive, and custom bodies on the ton command cars, the trucks followed the 1939 procurement doctrine, to "use commercial trucks with only a few modifications such as brush guards and towing pintles to fit them for military use."
The first of the -ton, 4x4, VC series military trucks were based on Dodge's 1939 commercial, one-ton rated model TC-series. The military VC models kept the same wheelbase and got the same civilian engine upgrade for 1940, but gained four-wheel drive, and a new internal technical code: T-202. Manufacturing of the half-ton Dodge VC-models began in 1940, making these the U.S. Army's first ever light-duty, mass-produced 4-wheel drive trucks. The soldiers also called the light command reconnaissance vehicles "jeeps," but this was also common with several other vehicles at the time. — before that term migrated to the quarter-tons, starting gradually in 1941.
A total of 4,640 VC models were built across six variants – mostly pick-ups and reconnaissance cars. On the one hand, these ton VC trucks proved so successful, that much greater quantities were immediately ordered, and they were further developed into the, ton WC models built in 1941. On the other hand, an even lighter and smaller 4x4 truck was needed: a quarter-ton, that would soon replace the Dodges as the U.S.' lightest 4x4 military trucks. Although no longer standard, the VC trucks remained in use until the end of the war. The Dodge VC models were built a year ahead, and in a slightly greater number than any of the pre-standard quarter-ton jeeps that followed.
In 1940, Dodge also built 6,472 four-wheel drive 1-ton trucks, under two U.S. contracts – one awarded to Dodge, and one to Fargo. The models VF-401 to VF-407, were a continuation of their experimental pre-war predecessors, the RF-40 and TF-40, still riding on a chassis of the same wheelbase. Production consisted of just over 6,000 closed cab, open bed cargo trucks, plus just under 400 dump-trucks.
Like on the -ton VC-series, the 1940 VF-400 1-ton models simply used civilian front sheet-metal, based on the 1939 commercial model, with a brush-guard fitted in front of the grille and headlights — but with a Dodge developed front driving axle, directional, cross-country tires, and a military cargo body. Importantly, one thousand of the VF-400 series cargo trucks were equipped with a power take-off, gear-driven Braden model MU capacity winch — a feature that was carried over on many of the subsequent and WC series models, directly from 1941. And although the light-duty WC models that followed, did not receive the VF-400's two-speed transfer cases, these did return on the 6x6 trucks, the and. An ambulance model,, was also designed, but only three units were built, likely experimental.
These proved to be the last of Dodge's 1-ton 4x4 trucks for the war. Although the Army had steadily taken the bulk of its trucks in this category from Dodge / Fargo up til then, further production of 1-ton 4x4 trucks was instead awarded to GM's Chevrolet G506, which became the standard in this segment for the rest of the war.
Aside from four-wheel drive trucks, production started for a militarized commercial 1-ton, rear-wheel drive truck in 1940 — initially Dodge's model VF-31, cargo under the government SNL number G-618. The 4x2 model VF-31 was succeeded by the model WF-31 for 1941 and 1942 — both on a wheelbase — and the 1942 model WF-32, closed cab, stake and platform cargo truck, on a wheelbase. After a modest production of 516 units of the WF-31, at least 9,500 Dodge WF-32 trucks were built, mostly for lend-lease to Russia.

1941–1942 — -ton WC series

The 1940 VC-series Dodge -ton 4x4s were well liked but considered only an interim solution, because they were essentially a modified civilian truck. At the outset of World War II a more military design was laid out. Dodge evolved the 1940 VC1 to VC6 into the equally half-ton rated WC series of military light trucks, produced in 38 model variants, of which 30 were four-wheel driven, in varying amounts — thousands of some models were produced, while only a few of some others were made. Where the military VCseries still used much civilian sheet-metal, distinguished by a brush-guard in front of the grille — the WCseries came with wide-open, almost flat fenders that prevented mud build-up, clogging rotation of the wheels — as well as a redesigned, sloping nose with an integrated, round, grated grille / brush-guard. A new ambulance with a fully enclosed, all-steel box rear body was designed, on a longer, 123 inch wheelbase; and PTO-driven winches were now fitted to some models.
The ton WC models were the first all-military design Dodge developed in the build-up to full mobilization for World WarII, and they were the U.S. Army's first standard light 4x4 trucks — prior to the quarter-tons — when the U.S. formally declared war in December 1941. Soldiers would sometimes call the new vehicles 'jeeps', as was still common practice before the term migrated to the yet to be introduced Willys and Ford -tons, and eventually stuck to those.
Both the Dodge half-ton VC and WC trucks were part of the Army series. Some 77,750 four-wheel drive ton WC numbered trucks were produced from late 1940 to early 1942, under War Department contracts. Additionally, aside from the fully military 4WD models, a small total of 1,542 two-wheel drive units retaining civilian sheet-metal were also supplied to the U.S. military, bearing WC model numbers in this same range. These models carried the SNL-code G-613, and brought the total number of half-ton WCseries up to some 79,300 units, and the grand total of all half-tonners to almost 84,000.
From August 1941, the Dodge T-211 models received the uprated 92 hp engine, that was from then on fitted to all WC trucks produced through August 1945: the T-215 half-tons, all of the G-502, -ton models, as well as the G-507, T-223, 6x6 trucks.

1942–1945 — -ton, G-502 WC series

In 1940 the Army revised its range of standard, payload-based, general-purpose truck classes: a "small truck" requirement was added, ; and after buying over 80,000 trucks from Dodge, the U.S. Army instead wanted rigs – and some more heavy categories were specified.
The Quartermaster General wanted to start direct negotiations with Dodge, GM and Mack for certain models immediately, but not until after February 1941 could the Quartermaster Corps choose manufacturers directly, based on their engineering and production capabilities. One deciding factor had to do with availability of certain critical components, like transfer cases and especially constant-velocity joints, not often used on commercial trucks until then, but all-wheel drive vehicles all needed these, to drive their front wheels smoothly. Additionally, all-wheel drive trucks needed two or three times the amount of driven axles, meaning more gears to cut for all the differentials. Produced until the war by a just a few specialized firms with limited capacity – from spring 1942, Ford, Dodge and Chevrolet joined in fabricating these in mass quantity, and Dodge were experienced in making quality, precision parts, since the earliest beginnings of the company.
While the Army bought many half-ton WC series trucks, Dodge had to replace them with new ton trucks. In late 1941, Dodge introduced a redesigned WCseries of 4x4 trucks, uprated to ton off-road capacity, and their SNL code changed to. The ton featured a lower profile truck bed that could seat eight troops, plus under seat stowage compartments; while service-parts remained 80 percent interchangeable with the existing ton series. Maintaining 80% service parts interchangeability with the ton models was of great value to both the field mechanics, and spare parts supply chain logistics. It also meant that production of the ton models could start very quickly, and they could be quickly deployed. The ton, WCtrucks remained in various uses to the end of World War II – from 1943 as "limited standard" vehicles.
Throughout the war, Dodge was the U.S. Army's sole producer of ton trucks, and built a total of 255,193 of these, across all variants, from April 1942 to August 1945.
Standard vehicles in the ton 4x4 class were the / Weapons Carrier, Command Reconnaissance, Carryall, and the Ambulance. In the mass-produced cargo/troop and command trucks, the and are identical to the and, but have a longer frame, extending further forward to the protruding front bumper with front-mounted winch.

1943–1945 — -ton, G-502 and 1-ton, 6x6, WC series

After the U.S. Army reorganized from using eight-troop rifle squads to twelve-men squads, a whole squad could no longer be carried as a unit in a single ton, 4x4, or truck. At the direction of Major General Courtney Hodges, Chief of Infantry, these troop- and weapons-carriers were therefore stretched in 1943, with an additional driven rear axle, to derive longer 6-wheel drive, 1ton trucks.
Using the same engine, gearbox, and cockpit, and sharing much of the other mechanicals, plus near-identical front-half sheet-metal as the -tons, the new 6x6,, 1tons' main difference was the use of a dual-range transfer-case, sourced out of the prior 1940, 1ton VF-400 models, instead of the single-speed box of the-tons and -tons. The result were the and cargo, troop and weapons carriers, to move whole 12-troop squad teams per vehicle. Despite having individual drive-shafts from the transfer-case to each rear axle, there is no way to disengage one of the rear axles to achieve 6x2 drive. The G-507 runs in either 6x4 or 6x6 configuration.
The WC-63 was equipped with a longer frame, housing an engine power take-off drive-shaft from the transfer-case forward, to drive a Braden MU2 winch, mounted on a more protruding front-bumper, reducing the approach angle. The winch capacity was originally rated at pull-strength, but in late 1943 the wire rope size was upgraded from to, the capacity rating was raised to, both on tons and the 6WDs.
The chassis and certain other components were strengthened in the design of the new, longer, double the payload rated models, and many of these changes were incorporated back into subsequent production of the -ton models as well. Although this caused some inconsistency in the mechanical uniformity of the -tons, it did keep parts the same as much as possible between the -tons and the new 1-tons, benefiting both the uniformity and ease of production of all the different models, as well as the tons, making them even more rugged from then on.

Further developments

Amphibious
Twelve G-614 half-ton capacity, 4x4, XAC-2 / experimental 'Aqua-Cheetah', amphibious vehicles were built in 1942, by the Amphibian Car Corporation. One unit was submitted to Britain for testing,, and the remaining eleven were subsequently rebuilt by the same firm, as G-552, XAC-3, amphibious 3/4ton trucks. Both the tons and the tons were built based on Dodge WC series mechanicals. The vehicles performed well in testing, but neither Britain nor the U.S. decided to standardize them.
Armored
A single armored car prototype was built, based on the 1ton, 6x6, Dodge.

Models table – overview

This table provides the relations between U.S. military and Dodge identification numbers, related to chassis payload classification in U.S. tons, wheels and drive, and description of body / vehicle type, in accordance with the U.S. Army Ordnance Standard Nomenclature List (SNL) vehicle catalog.
The U.S. government used vehicle numbers starting with 'G-', whereas Dodge indicated models sharing the same technical configuration by a common 'T-' number, and their individual model numbers starting with two letters, like 'WC-'. The U.S. Army simply considered the 1941 half-ton Dodge WC series as evolutions of the initial 1940 VC series – all within the half-ton, 4x4, SNL truck range.
In the case of two model codes separated by a slash, the first code refers to the vehicle without a winch, and the second code, in bold print, to the same vehicle, on a longer front frame, holding a front winch, typically resulting in a longer front overhang, and distinctly reduced approach angle. Not only were the winches driven by a power take-off from the engine, but unlike the later Dodge M-series trucks, on which an extension was bolted to the frame when mounting a winch — on the WCseries the winch equipped versions were actually built on a different, longer frame.
On the 1-ton rated VF-400 series trucks, the PTO-driven winch had a 10,000 pound capacity, but added almost 1,000 pounds to the vehicles weight, reducing the payload to 2400 pounds.
Numbers separated by a comma indicate similar models but with different secondary details.

Engines and drivetrains

All engines were liquid-cooled, gasoline, straight-six Chrysler flathead engines. Recommended fuel octane rating for the initial T-207 WC half-tons was just 60–65, going by the dashboard data plate.
The side-valve engines were mated to drive-trains of four-speed manual transmissions and a single-range transfer case, offering part-time four-wheel drive. Only the drive-trains in the 1ton models, the 1940 T203, trucks, and the 1943–1945,, T223 six-wheel drives, had a dual-ratio transfer-case. The low ratio on the 6x6, T223 transfer case gave a 1.5 : 1 reduction instead of the direct drive high gear.
The first batch of 1940, small half-ton Dodge VC models, received a, 79 horsepower engine, well above their initial commercial rating of 70 hp on the 1939 TC half-tons. The four-speed gearbox fitted, was a stock option on the civilian Dodges, and so were oil filters, oil-bath air cleaners, and heavy-duty generators. The 1941 model-year T207-series trucks were again classed as G-505 half-tons, but these were powered by a straight-six of 85 hp, taken from Dodge's - and one-ton commercial trucks. When the 1941 WC models were updated to T211 specifications, that initially remained so – but later T211s, and all of the final G505 half-ton WC series, got a L-head of 92 hp.
From the mid 1941, T211 half-ton WC models onwards, to 1945, through the production of all 255,200 ton T214 models, and the 43,200 ton, T223, stretched six-wheel drive trucks, this 92 hp, engine powered about 340,000 of all the Dodge WC series, basically unchanged.

Half-ton VC series

The 1940 Dodge / Fargo VC models formed the first production run in the U.S. military's range of half-ton, light four-wheel drive trucks. Created by Chrysler, based on Dodge's lightest, new for 1939, commercial half-ton TC models of "express" pickups, and their carry-all, the 1940 VC models formed the foundation for the subsequent 1941, G505, ton WC series trucks.
All variants used the same wheelbase as the shortest civilian trucks, but with the addition of part-time four-wheel drive. Bodywork and sheet metal on the military VC series pick-ups and carryall were the same as the civilian models — however, for the command reconnaissance and radio cars, a new, dedicated open five seater body was created, manufactured by Budd Company.
Also the same inline six, flathead engine was used, but Dodge raised its power output from a rating in the 1939 civilian TC, to at 3000 rpm for their 1940 light VC models, and for the Army's VCs. The transmission had 4 speeds, and the transfer case just one – it only shifted drive to the front axle, to engage or disengage four-wheel drive. On-road, it remained rear-wheel drive, to prevent binding that would damage the drivetrain while cornering, as there was no center differential.
The G-505 half-ton VC series came in six variants, numbered to, and internally T-202 by Dodge:
  • VC-1: Command Reconnaissance car – 2,155 units
  • VC-2: Radio Command Reconnaissance – 34 units
  • VC-3: Closed cab Pickup with bed seating for troops – 816 units
  • VC-4: Closed cab Pickup without bed seats – 4 units
  • VC-5: Open cab Pickup with bed seating for troops – 1,607 units
  • VC-6: Carry-all – 24 units
None of these trucks came with winches yet.
Delivered from early 1940 under a production contract, these 4,640 half-ton trucks were both the U.S. Army's first ever scale procurement of 'light' four-wheel drive vehicles – and their first light 4x4 trucks that military men called "jeeps" – as well as a part of Dodge's first official production contract for four-wheel drive trucks from the U.S. military. All prior sales, for the -ton trucks, although in the hundreds in 1934 and 1939, and even counting 1,700 in 1938, had been contracts for 'experimental' Army trucks.

Half-ton WC series

The half-ton, 4x4, Dodge WC series were evolutionary redesigns of the preceding VC series, retaining the military series code. Starting production in late 1940, until replacement by the 3/4ton models in early 1942, they progressed through three mechanical engineering versions, in barely a year and a half – while receiving the specification engine midway through production of the coded versions. Half-ton rated WC series models received thirty-eight numbers, roughly chronologically, in the to range, but skipping numbers, to, and to.
The WC series is immediately recognizable by its redesigned, now military sheet-metal. Wide-open, simplified front and rear fenders replaced the bulbous civilian ones, offering more wheel-travel, and less risk of wheels clogging stuck with thick mud in the wheel-well. The front brush-guard and grille were redesigned, replacing the civilian art-deco front with a single, integrated, upright, round welded grate.
The distribution across the versions was:
  • 31,935 units of the WC-1 through WC-11 models, with the engineering code and a engine with ;
  • 17,293 units of the WC-12 through WC-20 models, with the T-211 engineering code and initially the same engine, however during August 1941 the engine was increased to and, but the overall number was not changed on affected models
  • 28,537 units of the WC-21 through WC-27 and WC-40 through model, with the engineering code and a engine with 92 HP.
The T-207 range had an uprated 85 hp engine, and these units had front axles with Bendix-Weiss constant-velocity joints, whereas and models were given front axles either made by Bendix or with Rzeppa design CV joints, made by Ford.
From the T-211 models onwards, the rear brakes were instead of drums. Among the versions, no single WC model number was explicitly used for winch-equipped units.
The T-215 types introduced a military design dashboard with round gauges, replacing the civilian dash with square ones.
A further 1,542 rear-wheel drive units. These retained civilian bodywork, fenders and grilles, as well as regular front axles, and a one-ton on-road rating.

Common specifications

  • Drive: four-wheel drive — except for WC-36 to WC-39 and to
  • Wheelbase: – both on four-wheel and two-wheel drive models
  • *except for ambulances and phone line / emergency repair trucks
  • Track width: front and rear
  • *except just front track on rear-wheel drive only models
  • Tires: 7.50×16 in
  • Brakes: Hydraulic
  • Engine: 6 cylinder, in-line, side valve engine
  • Transmission: manual, 4 forward / 1 reverse
  • Transfer case: Single speed

-ton Ambulances

WC-9, WC-18, WC-27
Entering production during 1941 to early 1942, they were specifically designed to serve as military ambulances. These early variants are distinguishable from the later ones by having a curved radiator grille, while the later ones featured a flat grille. These versions were given a longer wheelbase.
  • Length:
  • Width:
  • Height:
  • Weight:
  • Payload:

-ton Carry-alls

WC-10, WC-17, WC-26, WC-36, WC-48
Carryall trucks with a nominal carrying capacity of. The, and followed engineering patterns T-207, T-211 and T-215 respectively — whereas the and were T-112, rear-wheel drive only models, retaining civilian bodywork with bulbous fenders.

-ton (Radio) Command Reconnaissance

WC-6, WC-15, WC-23
Command / reconnaissance cars.
WC-7, WC-24
Command / reconnaissance car with winch.
WC-8, WC-16, WC-25
Radio car / Command reconnaissance car with radio, 12 volt.

-ton Trucks, Closed Cab

WC-1, WC-5, WC-12, WC-14, WC-40
Closed cab, two seater pickups with a nominal carrying capacity of a. Some portion of these models were manufactured with winch, at least of the, the, and the, reducing the payload to — but no distinct model number was assigned for such units. The engine displacement was increased to the T-215's volume of mid-series, after engine No. 42001.

-ton Trucks, Open Cab

WC-3, WC-13, WC-21
Weapon carriers, two seater pickups with open cab. The open cab pickups could be fitted with an optional M24 machine gun mount, which bolted across the front of the bed. The mount could carry the M1918 Browning Automatic Rifle, as well as the M1919 Browning machine gun, and the 0.5 in M2 Browning machine gun.
  • Length:
  • Width:
  • Height: with top
  • Weight:
  • Payload:
WC-4, WC-22
Open cab weapons carrier, with Braden MU winch, and transverse seats, designed to tow the 37mm M3 anti-tank gun as well as carry the gun crew and ammunition. This type was usually issued to early tank destroyer units. 5570 built.
  • Length:
  • Width:
  • Height: with top
  • Weight: net
  • Payload:

-ton (Radio) Panel Vans

WC-11, WC-19, WC-42
Almost 1,400 panel van trucks, and panel van bodied radio communication cars. At first, regular panel van trucks were ordered: 642 units of, and 103 units of. The subsequent panel vans were however furnished and equipped as radio communication cars. The 650 radio panel vans almost outnumbered their bare transportation siblings, and they were also the only radio communication cars that Dodge built in a panel van body style in the entire VC and WC series range.
Almost half of production, 650 units, went to the British Empire under the U.S. Lend-Lease agreement.
There were also negligible numbers made with civilian style bodywork, similar to the 1940 VC-6 Carryall, with only rear-wheel drive, with the and internal codes – six units of, and a further eight as, in 1942.

-ton Telephone Service

WC-39, WC-43, WC-50
These models were built as technical service trucks for the U.S. Army Signal Corps, designed to install and repair hard telephone lines. Together with some earlier ton GMC/Chevrolet models, and the later ton and, they were also known by the Signal Corps as the K-50 trucks.
Of the two-wheel drive WC-39 and WC-50, only a single unit of each were built, but the four-wheel drive numbered 370 units.

-ton Trucks, Emergency Repair

WC-5, WC-14, WC-20, WC-40, WC-41
Just over one thousand emergency repair chassis and trucks were ordered within the half-ton Dodge, WC series. The Dodge SNL G-657 Master Parts List doesn't explicitly list most of them as built to serve as emergency repair trucks, but the Summary Report of Acceptances, Tank-Automotive Materiel, 1940–1945, shows that at least 956 emergency repair chassis and trucks were received by the Army, involving at least all of the,,, and models.
Dodge delivered at least all thirty WC-20, and most of the WC-41 units, as closed cabs with a bare chassis, on a wheelbase, fitted with dual rear wheels, though a minority, particularly of the,, and, were possibly built on a wheelbase; and some as pick-ups. Most were furnished with third party utility service rear bodies, as M1 emergency repair trucks, to provide mobile facilities for emergency ordnance repair. One other body-type was ordered: one T-211 oil servicing truck in 1941.
U.S. Gvmt. Contract nr.Tech modelUnits orderedVehicle / body type – as orderedUnits builtModel codeVehicle / body type – Dodge description Units acceptedSummary Report of Acceptances model / type
W-398-QM-8286T-20760Emergency Repair60Closed cab pickup––
W-398-QM-9388T-211268Emergency Repair268Closed cab pickup298Emergency Repair, chassis
W-398-QM-9388T-21130Emergency Repair, chassis30Closed cab – bare chassis298Emergency Repair, chassis
W-398-QM-10327T-215275Emergency Repair275Closed cab pickup275Emergency Repair
W-398-QM-10327T-215267Emergency Repair, chassis267Closed cab – bare chassis54 chassis
W-398-QM-10327T-215267Emergency Repair, chassis267Closed cab – bare chassis213Chassis, Emergency Repair
W-398-QM-11244T-21539Emergency Repair39Closed cab39Emergency Repair, chassis
W-398-QM-11592T-21577Emergency Repair, chassis77Emergency Repair, cab & chassis77Emergency Repair, chassis

Three-quarter-ton models

By late 1941, the Dodge WC range was significantly redesigned. All four-wheeled models were reinforced and uprated to a nominal three-quarter ton off-road payload rating, under the revised U.S.Army Ordnance Corps Supply catalog number; and later, for 1943, a stretched six-wheel drive, 1ton rated variant was developed, under supply code.
All models were widened to front and rear tracks of, widening the front track by as much as, and the rear track by on most models. The new axles were not only the same width, but also got the same differentials and axle carriers. The tires were widened from 7.50×16 to 9 inches wide. Moreover, the bulk production variants were significantly shortened, giving the vehicles much more square proportions, like on their younger ton brothers. On all the troops & weapons carriers, and command / reconnaissance & radio trucks, the wheelbase were all cut by almost half a meter, from a to a wheelbase. Only ambulances, carry-alls, and technical service trucks kept a long wheelbase. Panel vans were dropped from the range and no longer made.
The big production volume models – the WC-51/-52 and the WC-56/-57/-58 – also got literally more square bodies; with more square, shorter and wider, length to width ratios. The integrated grille / brush-guard became straight, and the hoods became lower and wider, and were flattened – both as in losing their previous curvature, and now just being horizontal – so they became more useful as an improvised table-top, and the front windows / windshields on these models could now also be folded forward, to lay flat on their hoods, just like on the -ton jeeps. Under the hood, the -tons kept the 6-cylinder inline, L-head engine of 92 hp gross, from the later model halfton WC series.
The biggest volume production variants, the WC-51 and-52 pick-up / troops and weapons-carrier models, received a completely redesigned rear bed, that mostly consisted of two longitudinal, rectangular boxes, that integrated the rear wheel wells with under-seat stowage compartments fore and aft of the rear wheels, while now seating the troops sideways and on top of the rear wheels, facing each other, instead of a in a commercial, "step-side" bed, in between the wheels. The new bed/box design widened these models to 6 ft 11 in, and offered much more space for the troops' backpacks and gear, between their feet, and under the seats. Asingle such truck, at just long, offered practical all-terrain transportation for a full eight man rifle squad, their weapons and gear.
With the nickname 'jeep' now moving on to the smaller ton trucks, some soldiers called the Dodges 'Beeps' instead.
Eventually, almost half of the more than fifty different WCseries models manufactured – almost 183,000 trucks – were WC51 & WC52 cargo/troop and weapons carriers — and one third of those with an engine-powered front winch.

-ton Ambulances

WC-54
The WC-54 Truck, 3/4 ton, 4×4 Ambulance, Dodge, was produced as an ambulance, but a few were modified to serve as radio/telephone trucks with the US Signal Corps. A total of 26,002 units were built from 1942 through 1944, after which the ambulance was redesigned, and replaced by the in 1945.
  • Length:
  • Width:
  • Height:
  • Weight:
  • Payload:
WC-64
The WC-64 KD Truck, 3/4 ton, 4x4 Ambulance Dodge was an ambulance based on the same chassis as the but with a knock-down body designed to increase the number of vehicles that could be shipped at the same time. The rear boxes were supplied in two major parts: lower and upper. The lower part of the box was attached to the chassis at the factory, while the upper box was crated for installation in the field. 3,500 Knock-down ambulances were built between the beginning of 1945 and the end of the war, the great majority went to allies under lend-lease:
  • 1,123 to the Free French forces
  • 644 to British Commonwealth
  • 475 to China
  • 149 to Brazil and 82 to other Latin American republics

-ton Carryall

WC-53
A carryall, the WC-53 was mechanically largely identical to the ambulance, but its body was the 1939 civilian carryall, modified with the wide open military fenders and grate-like grille, square box engine housing, and heavy butch front bumper, like the other models.
But the carryall had some comforts – not only a cabin heater, but flexible seating for up to eight people, and all six side windows were wind-up opening. The seating consisted of a front 2-seat bench for the driver and a front center passenger, a folding front-right passenger seat to allow rear access, a two-seat second row bench, leaving access to the rear full width three-seat bench. Upholstery was often civilian grade naugahyde, fit for higher officers. Both the third and 2nd row bench-seats were removable, to increase rear luggage space as needed, their legs held in metal mountings, inset in the full length and width wooden floor.

WC-53s were also fitted as radio trucks with a sideways bench on the left side, to seat the radio operator, and perhaps a commander and clerk. The right-side running-board came standard with a box for a 2nd battery, to provide enough voltage for radio equipment.
The driver's side door has a mount to carry the spare wheel, but although the door was fully functional, it could not be opened while holding a wheel, so the driver would then have to enter from the passenger side. The rear end had a horizontally split tailgate.
8,400 : Truck, 3/4 ton, 4×4 Dodge Carryall were built. No carryalls came from the factory with a winch, though there was a field modification available.
  • Length:
  • Width:
  • Height:
  • Weight:
  • Payload:

-ton (Radio) Command Reconnaissance Cars

WC-56
The WC-56 Truck, Command Reconnaissance, 3/4 ton, 4x4 w/o Winch, Dodge was a command and reconnaissance vehicle akin to an oversized quarter-ton jeep or VW Kübelwagen, offering fixed bench-seats, wide enough for three-abreast seating for adults – both front and rear. In addition, large wooden planks served as map-reading tables and make-shift writing-desks; in the front it slid in/out of the dashboard for the right front passenger, either over or under the large glove box. In the rear, a full-width plank was normally tucked behind the front seat-back, but could be pulled up and onto the occupants' laps, to unfold large maps. The soft-top included side-curtains, for better weather shielding.
The command cars did not prove as popular as the small jeeps, as they were heavier and not as maneuverable, plus its distinctive profile made them a target, whether you had a WC-56, -57, or -58. Some 21,156 units were built of the basic WC-56 version.
  • Length: 13 ft 10 in
  • Width: 6 ft 7 in
  • Height: 6 ft 9 in
  • Weight: 5,335 lb
  • Payload: 1,750 lb
WC-57
The WC-57 Truck, Command Reconnaissance, 3/4 ton, 4x4 w/Winch Dodge was identical to the, but it carried a power take-off driven Braden MU2 7,500 lb capacity winch on a 10 inch longer protruding front bumper and frame, reducing its approach angle.
6,010 units were built in addition to the WC-56s.
  • Length: 14 ft 8 in
  • Width: 6 ft 7 in
  • Height: 6 ft 9 in
  • Weight: 5,644 lb
  • Payload: 1,750 lb
WC-58
The WC-58 Truck, Radio, 3/4 ton, 4×4 w/o Winch, Dodge was identical to the Command / Reconnaissance Car, but fitted with a Signal Corps Radio set in front of the rear seat, and a 12-volt electrical system. Some models may have been built, based on the with winch, as well. A total of 2,344 units of WC-56 and WC-57 were radio equipped, but once all command cars started receiving 12-Volt electrical systems, the WC-58s no longer constituted additional production, but were instead a converted fraction of the and production. As other -ton models also started to receive 12-Volt electrical systems, they too were getting fitted with radios as needed. At the end of it all, a total of 2,344 radio equipped command cars were counted as.
  • Length: 13 ft 10 in / 14 ft 7 in with winch
  • Width: 6 ft 7 in
  • Height: 6 ft 9 in
  • Weight: 5,644 lb
  • Payload: 1,750 lb

-ton Trucks, Weapons Carrier

WC-51 and WC-52
The G-502, WC-51 & WC-52: "Truck, Cargo, -ton, 4x4, Weapons Carrier", had largely redesigned bodies and frames, compared to their half-ton, 1940–1941 forebears, yet retained mechanically as much as possible — improving what was necessary, while maintaining supply, logistics, and training continuity. The design was now blatantly more jeep-like, with a much shorter, lower, wider, versatile, open cab pickup body. The hood became flat and horizontal, and the windshield could now also be folded forward, flat on it. With the top and bows down, the and -52 followed the low-profile design doctrine of the time. Engine and drive-train were almost completely carried over from the half-tons, except for the uprated, wider track axles, which were now closer together, for a wheelbase.
The WC-51 and -52 could be fitted with an optional M24A1 machine gun mount, or other devices. The M24A1 mount bolted across the front of the bed, and could carry the M1918 Browning Automatic Rifle, the M1919 Browning machine gun, or the M2 Browning machine gun.
Lack of a winch gave the a shorter front overhang, and thus a better approach angle. The not only differed from the by having a power take-off driven Braden MU2 7,500 lb capacity winch on the front bumper, but to accommodate it, the was actually built on its own, longer frame. With about every third unit carrying a winch, these were thus rarely ever retrofitted.
Almost three quarters of Dodge's 255,195 total ton,, WC series production, were built as and, cargo, troops and weapon carriers. 123,541 were built without winch as the, and 59,114 with a front winch as — for a total of 182,655 units. When adding the 5,380, M6 gun motor carriages, that were later downgraded back to specification, it brings the total number to over 188,000 of these models. Although nearly a quarter of that were passed on to allies, mostly through Lend-Lease, once the 1939 U.S. Army reorganization from 8man to 12man (rifle) squads got tied more closely into troop-car procurement, Dodge received orders for a similar amount of the stretched, 12troop capacity, &, 1ton, 6x6 trucks.
  • Length:, or with winch
  • Width: 6 ft 11 in
  • Height : 6 ft 10 in
  • Height : 5 ft 2 in
  • Weight: 5,250 lb net – 5,550 lb net with winch
  • Payload: 1,750 lb
  • Tires: 9.00 x 16 in., 8ply
A substantial amount – almost a quarter – of all the ton weapons carriers, were provided through Lend-Lease to various Allies:

-ton truck, M6 gun motor carriage

WC-55
The M6 37 mm gun motor carriage, 3/4-ton, 4×4, or fully described "M6 Fargo gun motor carriage with 37 mm anti-tank gun,", was a modified [List of U.S. military vehicles by supply catalog designation#G500 to G599|] Dodge, designed and built to carry an M3A1 37mm anti-tank gun combined with gun shield, mounted on its cargo bed, facing rearward. The with gun combination was designated by Standard Nomenclature List supply catalog number [List of U.S. military vehicles by supply catalog designation#G100 to G199|]. A total of 5,380 were built by Fargo in 1942, but most were later dismantled / downgraded and returned to service as cargo trucks.
Fielded as a stopgap design from late 1942 in North Africa, in limited use with the US Army Tank Destroyer Battalions, and in the Pacific War in 1943/1944, improvements in enemy tanks quickly rendered the 37mm gun underpowered, and better guns became available. The was first downgraded to "limited standard" in 1943, and subsequently declared obsolete, finally by early 1945.
  • Length: 14 ft 8 in
  • Width: 7 ft 2 in
  • Height: 8 ft 2 in to top of gun shield
  • Weight: 5,600 lb
  • Storage: 80 rounds of 37mm munitions

-ton Telephone Service

WC-59
The WC-59 Truck, Telephone Maintenance, 3/4 ton, 4×4 Dodge was designed to install and repair telephone lines. Based on the same chassis as the ambulances, sharing a longer wheelbase than the regular ton WC series. The spare wheel was carried behind the seats, and a step ladder fitted where the spare wheel normally would have been. 549 units were built. The bespoke bed made it a K-50 truck to the Signal Corps. These were initially fitted to both Dodge and Chevrolet chassis.
  • Length: 16 ft 0 in
  • Width: 6 ft 6 in
  • Height: 6 ft 9 in
  • Weight: 5,357 lb
  • Payload: 1,750 lb
WC-61
The WC-61 Light Maintenance Truck, 3/4 ton, 4×4 Dodge was also designed to install and repair telephone lines. Replacement for the, the had the step ladder mounted on the roof, the spare wheel was still fitted behind the seats, and the tool trunks were accessible from the outside. Just 58 were built. The US Signal Corps referred to these as the K-50B truck.
  • Length: 15 ft 6 in
  • Width: 6 ft 10 in
  • Height : 7 ft 5 in
  • Weight: 5,952 lb
  • Payload: 1,750 lb

-ton Truck, Emergency Repair

WC-60
The WC-60 chassis, fitted with a bed similar to the by the American Coach and Body Co. of Cleveland, Ohio, formed the M2 Emergency Repair truck, 3/4 ton, 4×4 Dodge, a mobile workshop designed for field maintenance. Its open-topped service-type bed featured numerous tool trunks and stowage bins, accessible from the outside. 296 units were built.
  • Length: 15 ft 6 in
  • Width: 6 ft 10 in
  • Height: 7 ft 5 in
  • Weight: 5,952 lb
  • Payload: 1,750 lb

One-and-a-half-ton models

WC-62

The 'G-507 Cargo and Personnel Carrier, 1-ton, 6x6 Truck, Dodge was based on a lengthened Weapons Carrier with an extra axle added. When the U.S. Army enlarged rifle squads from eight to twelve men, the ton no longer sufficed, and a longer 6×6 variant was created that used most of the mechanical parts and the whole front sheet metal and cabin of the. The trucks could be driven by all six wheels or by the four rear wheels only.
A number of components needed further strengthening in this design, and many of these reinforcements were also incorporated in subsequent tons production – both making these even more robust, as well as benefiting the spare parts and supply-chain, by keeping the most future parts suitable and interchangeable on the tons and the tons. Six-wheel drive production amounted to 43,224 units total, — 23,092 units without winch, and 20,132 variants with'' winch. One prototype was produced as an armored car.
A total of 6,344 WC-62 and WC-63 cargo trucks were provided to World War II Allies — 4,074 to the Free French forces, 2,123 to British, and 137 units to Brazil.
  • Length: 17 ft 11 in
  • Width: 6 ft 11 in
  • Height : 7 ft 3 in
  • Height : 5 ft 2 in
  • Weight: 6,925 lb
  • Payload: 3,300 lb

WC-63

The WC-63 Truck, Cargo and Personnel Carrier, 1 ton, 6×6 with Winch, Dodge Weapons Carrier was based on a lengthened with an extra axle added. Identical to the but fitted with a PTO-powered Braden MU2 winch, initially of, later capacity.
  • Length: 18 ft 9 in
  • Width: 6 ft 11 in
  • Height : 7 ft 3 in
  • Height : 5 ft 2 in
  • Weight: 7,175 lb
  • Payload: 3,300 lb

Comprehensive models table

The table below lists the comprehensive set of models in the Dodge WC series family showing the different codes that were assigned together with each model's core specifications.
Different colors have been used to code groupings for maximum convenience, based on nominal payload rating, model family, and wheels and drive.
Lend-lease models, and Canadian-built models are presented in red, at the bottom.
Payload rating Dodge model US Army SNL-nr. Dodge
T-code		 Wheels & drive
body code 		Model and body description Winch Years Number built Wheel base Length Width Height Payload
'-ton VC-1 G-505 T-202 4×4 Command reconnaissance 1940 2,155
'-ton VC-2 G-505 T-202 4×4 Radio command reconnaissance 1940 34
'-ton VC-3 G-505 T-202 4×4 Pick-up, closed cab, with troop seats 1940 816
'-ton VC-4 G-505 T-202 4×4 Pick-up, closed cab, no bed seats 1940 4
'-ton VC-5 G-505 T-202 4×4 Pick-up, open cab / Weapon Carrier; transverse seats 1940 1,607
'-ton VC-6 G-505 T-202 4×4 Carry-all 1940 24
'-ton WC-1 G-505 T-207 4×4 Pick-up, closed cab; longitudinal seats 1941 2,573 /
'-ton WC-3 G-505 T-207 4×4 Pick-up, open cab / Weapon Carrier; transverse seats 1941 7,808
'-ton WC-4 G-505 T-207 4×4 Pick-up, open cab / Weapon Carrier; transverse seatsw / winch 1941 5,570
'-ton WC-5 G-505 T-207 4×4 Pick-up, closed cab; no bed seating 1941 60 /
'-ton WC-6 G-505 T-207 4×4 Command reconnaissance 1941 9,365
'-ton WC-7 G-505 T-207 4×4 Command reconnaissancew / winch 1941 1,438
'-ton WC-8 G-505 T-207 4×4 Radio command reconnaissance 1941 548
'-ton WC-9 G-505 T-207 4×4 Ambulance 1941 2,288
'-ton WC-10 G-505 T-207 4×4 Carry-all 1941 1,643
'-ton WC-11 G-505 T-207 4×4 Panel van 1941 642
'-ton WC-12 G-505 T-211 4×4 Pick-up, closed cab 1941 6,047 /
'-ton WC-13 G-505 T-211 4×4 Pick-up, open cab / Weapon Carrier 1941 4,019 /
'-ton WC-14 G-505 T-211 4×4 Pick-up, closed cab / Emergency Repair 1941 268 /
'-ton WC-15 G-505 T-211 4×4 Command reconnaissance 1941 3,980
'-ton WC-16 G-505 T-211 4×4 Radio command reconnaissance 1941 1,284
'-ton WC-17 G-505 T-211 4×4 Carry-all 1941 274
'-ton WC-18 G-505 T-211 4×4 Ambulance 1941 1,555
'-ton WC-19 G-505 T-211 4×4 Panel van 1941 103
'-ton WC-20 G-061 T-211 4×4 Emergency repair, M1, Closed cab chassis 1941 30 /
'-ton WC-21 G-505 T-215 4×4 Pick-up, open cab / Weapon Carrier; transverse seats 1941–1942 14,287 /
'-ton WC-22 G-505 T-215 4×4 Pick-up, open cab / Weapon Carrierw / winch 1941 1,900 /
'-ton WC-23 G-505 T-215 4×4 Command reconnaissance 1941–1942 2,637 /
'-ton WC-24 G-505 T-215 4×4 Command reconnaissancew / winch 1941–1942 1,412 /
'-ton WC-25 G-505 T-215 4 x 4 Radio command reconnaissance 1941–1942 1,630 /
'-ton WC-26 G-505 T-215 4 x 4 Carry-all 1941–1942 2,900 /
'-ton WC-27 G-505 T-215 4×4 Ambulance 1941–1942 2,579
'-ton WC-36 G-613 T-112 4×2 Carry-all 1941 400
'-ton WC-37 G-613 T-112 4×2 Panel van — VC model civilian body 1941 6
'-ton WC-38 G-613 T-112 4×2 Pick-up, closed cab – VC model civilian body 1941 362
'-ton WC-39 G-613 T-112 4×2 Telephone installation, K-50 1941 1
'-ton WC-40 G-505 T-215 4×4 Pick-up, closed cab / Emergency Repair 1941 275 /
'-ton WC-41A G-505 T-215 4×4 Pick-up, closed cab / Emergency Repair 1941 39 /
'-ton WC-41B G-061 T-215 4×4 Emergency repair, M1, Closed cab chassis 1941–1942 306 /
'-ton WC-42 G-505 T-215 4×4 Radio – Panel van 1942 650 /
'-ton WC-43 G-505 T-215 4×4 Telephone installation, K-50 1942 370
'-ton WC-47 G-613 T-112 4×2 Pick-up, closed cab — VC model civilian body 1942 390
'-ton WC-48 G-613 T-112 4×2 Carry-all 1942 374
'-ton WC-49 G-613 T-112 4×2 Panel van — VC model civilian body 1942 8
'-ton WC-50 G-613 T-112 4×2 Telephone installation, K-50 1942 1
'-ton WC-51 G-502 T-214 4×4 Pick-up, open cab / Weapon Carrier 1942–1945 123,541
'-ton WC-52 G-502 T-214 4×4 Pick-up, open cab / Weapon Carrierw / winch 1942–1945 59,114
'-ton WC-53 G-502 T-214 4×4 Carry-all 1942–1943 8,400
'-ton WC-54 G-502 T-214 4×4 Ambulance 1942–1944 26,002
'-ton WC-55 G-121 T-214 4×4 Pick-up, open cab "M6 gun motor carriage" w / winch 1942 5,380
'-ton WC-56 G-502 T-214 4×4 Command reconnaissance 1942–1944 21,156 /
'-ton WC-57 G-502 T-214 4×4 Command reconnaissance w / winch 1942–1944 6,010 /
'-ton WC-58 G-502 T-214 4 x 4 Radio command reconnaissance unclear 1942 2,344 /
'-ton WC-59 G-502 T-214 4 x 4 Telephone installation, K-50 1942–1943 549 /
'-ton WC-60 G-061 T-214 4×4 Emergency repair, M2, Closed cab chassis 1943 300
'-ton WC-61 G-502 T-214 4×4 Phone / Maintenance, K-50B 1943 58
'-ton WC-64 G-502 T-214 4×4 Ambulance, Knock-down 1945 3,500
1-ton VF-401 G-621 T-203 4×4 USM-BT-3 Pick-up / cargo, closed cab 1940 3,122
1-ton VF-402 G-621 T-203 4×4 USM-BT-3 Pick-up / cargo, closed cabw / winch 1940 491
1-ton VF-403 G-621 T-203 4×4 USM-BT-4 Dump truck, closed cab 1940 323
1-ton VF-404 G-621 T-203 4×4 USM-BT-3 Pick-up / cargo, closed cab 1940 1,956
1-ton VF-405 G-621 T-203 4×4 USM-BT-3 Pick-up / cargo, closed cabw / winch 1940 509
1-ton VF-406 G-621 T-203 4×4 USM-BT-4 Dump truck, closed cab 1940 67
1-ton VF-407 G-621 T-203 4×4 USM-BT-18 Ambulance 1940 3
1-ton WC-62 G-507 T-223 6×6 USM-BT-25/26 Cargo Carrier1943–1945 23,092 89 in /
84 in
1-ton WC-63 G-507 T-223 6×6 USM-BT-23/24 Cargo Carrierw / winch1943–1945 20,132 89 in /
84 in
1-ton T-203B T-203-B 4×4Lend-lease Cargo truck / Lend-Lease to Russia 1940 1,500
1-ton WF-32 G-618 T-118 4×2 Lend-lease;
made in Iran		 Closed cab, stake and platform 1942–1944 9,600
'-ton D8A — T-212 4×4 Canadian production Pick-up, open cab / Weapon Carrier 3,001
-ton D3/4 APT — T-236 4×4 Canadian production Pick-up, open cab / Weapon Carrier; Air-Portablew / winch 1945 11,750

Service history

Although Chrysler / Dodge supplied over 380,000 WC-series to the war effort – more than the number of MB jeeps actually built by Willys, and the vehicles served with equal versatility – the Dodge WC-series, that were nicknamed "jeeps" by the soldiers, before that moniker subsequently migrated to its quarter-ton brothers, never received any comparable level of fame. The Dodge WC-series have therefore been called one of WWII's unsung heroes.

Lend-Lease

Almost 60,000 Dodge WC series models were provided to the U.S.' allies of World War II under the Lend-Lease program:
  • 650 of the total 1,400 -ton Panel vans built, possibly with radio, went to the British,
  • 886 -ton Carry-alls went mainly to the British and the Soviets, with small numbers to various other countries,
  • over 2,500 of the total 3,500 WC-64, -ton knock-down ambulances went primarily to the Free French, the British, and to China,
  • some 3,800 -ton WC-56 / WC-57 Command Cars went mainly to the British, the Free French, and to China,
  • plus a further 650 -ton Radio cars, likely WC-58 model, also for the British,
  • the bulk of lend-lease Dodges – over 44,000 units – were WC-51 and WC-52 -ton Troops and Weapons Carriers – see their section above,
  • and lastly, 6,344 of WC-62 and WC-63 1-ton, 6x6 Cargo, Troops and Weapons Carriers were provided – mainly to the French, and to the British.
To the Soviets, the almost 25,000 new 1942 all-wheel drive -ton multi-purpose WC series were so fundamentally innovative, that they fitted no standard Red Army category. Russia much appreciated these vehicles, that perfectly filled the gap between 4WD automobiles and heavy trucks, and simply called them "Dodge three-quarters".

Former operators

;
nicknamed as Jipão.
; Philippine Republic
At least two survived in running condition in Russian museums:

In popular culture

Dodge WC series vehicles are visible in many World War II movies, and American TV series. One of the most conspicuous examples is the frequent use of the WC-54 ambulances in the acclaimed M*A*S*H TV series, situated in the Korean War.
In many WW II films, directors would place high-ranking allied officers in Dodge Command Cars, although in reality, the German military quickly realized that personnel riding in the Command Cars were typically prime targets, and Allied generals and dignitaries would in reality prefer to ride in regular jeeps, to prevent advertising themselves as high-profile targets.
It also appears in Oppenheimer, in Los Alamos.

General references

  • Richards, T. and Clarke, R.M. Dodge WW2 military portfolio 1940-45. Brookland Books LTD