Signal integrity


Signal integrity or SI is a set of measures of the quality of an electrical signal. In digital electronics, a stream of binary values is represented by a voltage waveform. However, digital signals are fundamentally analog in nature, and all signals are subject to effects such as noise, distortion, and loss. Over short distances and at low bit rates, a simple conductor can transmit this with sufficient fidelity. At high bit rates and over longer distances or through various mediums, various effects can degrade the electrical signal to the point where errors occur and the system or device fails. Signal integrity engineering is the task of analyzing and mitigating these effects. It is an important activity at all levels of electronics packaging and assembly, from internal connections of an integrated circuit, through the package, the printed circuit board, the backplane, and inter-system connections. While there are some common themes at these various levels, there are also practical considerations, in particular the interconnect flight time versus the bit period, that cause substantial differences in the approach to signal integrity for on-chip connections versus chip-to-chip connections.
Some of the main issues of concern for signal integrity are ringing, crosstalk, ground bounce, distortion, signal loss, and power supply noise.

History

Signal integrity primarily involves the electrical performance of the wires and other packaging structures used to move signals about within an electronic product. Such performance is a matter of basic physics and as such has remained relatively unchanged since the inception of electronic signaling. The first transatlantic telegraph cable suffered from severe signal integrity problems, and analysis of the problems yielded many of the mathematical tools still used today to analyze signal integrity problems, such as the telegrapher's equations. Products as old as the Western Electric crossbar telephone exchange, based on the wire-spring relay, suffered almost all the effects seen today - the ringing, crosstalk, ground bounce, and power supply noise that plague modern digital products.
On printed circuit boards, signal integrity became a serious concern when the transition times of signals started to become comparable to the propagation time across the board. Very roughly speaking, this typically happens when system speeds exceed a few tens of MHz. At first, only a few of the most important, or highest speed, signals needed detailed analysis or design. As speeds increased, a larger and larger fraction of signals needed SI analysis and design practices. In modern circuit designs, essentially all signals must be designed with SI in mind.
For ICs, SI analysis became necessary as an effect of reduced design rules. In the early days of the modern VLSI era, digital chip circuit design and layout were manual processes. The use of abstraction and the application of automatic synthesis techniques have since allowed designers to express their designs using high-level languages and apply an automated design process to create very complex designs, ignoring the electrical characteristics of the underlying circuits to a large degree. However, scaling trends brought electrical effects back to the forefront in recent technology nodes. With scaling of technology below 0.25 μm, the wire delays have become comparable or even greater than the gate delays. As a result, the wire delays needed to be considered to achieve timing closure. In nanometer technologies at 0.13 μm and below, unintended interactions between signals became an important consideration for digital design. At these technology nodes, the performance and correctness of a design cannot be assured without considering noise effects.
Most of this article is about SI in relation to modern electronic technology - notably the use integrated circuits and printed circuit board technology. Nevertheless, the principles of SI are not exclusive to the signalling technology used. SI existed long before the advent of either technology, and will do so as long as electronic communications persist.

On-chip signal integrity

Signal integrity problems in modern integrated circuits can have many drastic consequences for digital designs:
  • Products can fail to operate at all, or worse yet, become unreliable in the field.
  • The design may work, but only at speeds slower than planned
  • Yield may be lowered, sometimes drastically
The cost of these failures is very high, and includes photomask costs, engineering costs and
opportunity cost due to delayed product introduction. Therefore, electronic design automation tools have been developed to analyze, prevent, and correct these problems.
In integrated circuits, or ICs, the main cause of signal integrity problems is crosstalk.
In CMOS technologies, this is primarily due to coupling capacitance, but in general it may be caused by mutual inductance, substrate coupling, non-ideal gate operation, and other sources. The fixes normally involve changing the sizes of drivers and/or spacing of wires.
In analog circuits, designers are also concerned with noise that arise from physical sources, such as thermal noise, flicker noise, and shot noise. These noise sources on the one hand present a lower limit to the smallest signal that can be amplified, and on the other, define an upper limit to the useful amplification.
In digital ICs, noise in a signal of interest arises primarily from coupling effects from switching of other signals. Increasing interconnect density has led to each wire having neighbors that are physically closer together, leading to increased crosstalk between neighboring nets. As circuits have continued to shrink in accordance with Moore's law, several effects have conspired to make noise problems worse:
  • To keep resistance tolerable despite decreased width, modern wire geometries are thicker in proportion to their spacing. This increases the sidewall capacitance at the expense of capacitance to ground, hence increasing the induced noise voltage.
  • Technology scaling has led to lower threshold voltages for MOS transistors, and has also reduced the difference between threshold and supply voltages, thereby reducing noise margins.
  • Logic speeds, and clock speeds in particular, have increased significantly, thus leading to faster transition times. These faster transition times are closely linked to higher capacitive crosstalk. Also, at such high speeds the inductive properties of the wires come into play, especially mutual inductance.
These effects have increased the interactions between signals and decreased the noise immunity of
digital CMOS circuits. This has led to noise being a significant problem for digital ICs that must be considered by every digital chip designer prior to tape-out. There are several concerns that must be mitigated:
  • Noise may cause a signal to assume the wrong value. This is particularly critical when the signal is about to be latched, for a wrong value could be loaded into a storage element, causing logic failure.
  • Noise may delay the settling of the signal to the correct value. This is often called noise-on-delay.
  • Noise may cause the input voltage of a gate to drop below ground level, or to exceed the supply voltage. This can reduce the lifetime of the device by stressing components, induce latchup, or cause multiple cycling of signals that should only cycle once in a given period.

    Finding IC signal integrity problems

Typically, an IC designer would take the following steps for SI verification:
  • Perform a layout extraction to get the parasitics associated with the layout. Usually worst-case parasitics and best-case parasitics are extracted and used in the simulations. For ICs, unlike PCBs, physical measurement of the parasitics is almost never done, since in-situ measurements with external equipment are extremely difficult. Furthermore, any measurement would occur after the chip has been created, which is too late to fix any problems observed.
  • Create a list of expected noise events, including different types of noise, such as coupling and charge sharing.
  • Create a model for each noise event. It is critical that the model is as accurate as necessary to model the given noise event.
  • For each signal event, decide how to excite the circuit so that the noise event will occur.
  • Create a SPICE netlist that represents the desired excitation, to include as many effects as necessary.
  • Run SPICE simulations. Analyze the simulation results and decide whether any re-design is required. It is common to analyze the results with an eye pattern and by calculating a timing budget.
Modern signal integrity tools for IC design perform all these steps automatically, producing reports that give a design a clean bill of health, or a list of problems that must be fixed. However, such tools generally are not applied across an entire IC, but only selected signals of interest.

Fixing IC signal integrity problems

Once a problem is found, it must be fixed. Typical fixes for IC on-chip problems include:
  • Removing impedance discontinuities. Finding places where significant shifts in the impedance exist and adjusting the geometry of the path to shift the impedance to better match the rest of the path.
  • Driver optimization. You can have too much drive, and also not enough.
  • Buffer insertion. In this approach, instead of upsizing the victim driver, a buffer is inserted at an appropriate point in the victim net.
  • Aggressor downsizing. This works by increasing the transition time of the attacking net by reducing the strength of its driver.
  • Add shielding. Add shielding of critical nets or clock nets using GND and VDD shields to reduce the effect of crosstalk.
  • Routing changes. Routing changes can be very effective in fixing noise problems, mainly by reducing the most troublesome coupling effects via separation.
Each of these fixes may possibly cause other problems. This type of issue must be addressed as part of design flows and design closure. Re-analysis after design changes is a prudent measure.