Incineration
Incineration is a waste treatment process that involves the combustion of substances contained in waste materials. Industrial plants for waste incineration are commonly referred to as waste-to-energy facilities. Incineration and other high-temperature waste treatment systems are described as "thermal treatment". Incineration of waste materials converts the waste into ash, flue gas and heat. The ash is mostly formed by the inorganic constituents of the waste and may take the form of solid lumps or particulates carried by the flue gas. The flue gases must be cleaned of gaseous and particulate pollutants before they are dispersed into the atmosphere. In some cases, the heat that is generated by incineration can be used to generate electric power.
Incineration with energy recovery is one of several waste-to-energy technologies such as gasification, pyrolysis and anaerobic digestion. While incineration and gasification technologies are similar in principle, the energy produced from incineration is high-temperature heat whereas combustible gas is often the main energy product from gasification. Incineration and gasification may also be implemented without energy and materials recovery.
In several countries, there are still concerns from experts and local communities about the environmental effect of incinerators.
In some countries, incinerators built just a few decades ago often did not include a materials separation to remove hazardous, bulky or recyclable materials before combustion. These facilities tended to risk the health of the plant workers and the local environment due to inadequate levels of gas cleaning and combustion process control. Most of these facilities did not generate electricity.
Incinerators reduce the solid mass of the original waste by 80–85% and the volume by 95–96%, depending on composition and degree of recovery of materials such as metals from the ash for recycling. This means that while incineration does not completely replace landfilling, it significantly reduces the necessary volume for disposal. Garbage trucks often reduce the volume of waste in a built-in compressor before delivery to the incinerator. Alternatively, at landfills, the volume of the uncompressed garbage can be reduced by approximately 70% by using a stationary steel compressor, albeit with a significant energy cost. In many countries, simpler waste compaction is a common practice for compaction at landfills.
Incineration has particularly strong benefits for the treatment of certain waste types in niche areas such as clinical wastes and certain hazardous wastes where pathogens and toxins can be destroyed by high temperatures. Examples include chemical multi-product plants with diverse toxic or very toxic wastewater streams, which cannot be routed to a conventional wastewater treatment plant.
Waste combustion is particularly popular in countries such as Japan, Singapore and the Netherlands, where land is a scarce resource. Denmark and Sweden have been leaders by using the energy generated from incineration for more than a century, in localised combined heat and power facilities supporting district heating schemes. In 2005, waste incineration produced 4.8% of the electricity consumption and 13.7% of the total domestic heat consumption in Denmark. A number of other European countries rely heavily on incineration for handling municipal waste, in particular Luxembourg, the Netherlands, Germany, and France.
History
The first UK incinerators for waste disposal were built in Nottingham by Manlove, Alliott & Co. Ltd. in 1874 to a design patented by Alfred Fryer. They were originally known as destructors.The first US incinerator was built in 1885 on Governors Island in New York, NY. The first facility in Austria-Hungary was built in 1905 in Brunn.
Technology
There are various types of incinerator plant design: moving grate, fixed grate, multiple hearth, rotary-kiln, and fluidised bed. Modern incinerators include pollution mitigation equipment such as flue gas cleaning.Burn pile
The burn pile or the burn pit is one of the simplest and earliest forms of waste disposal, consisting of a mound of combustible materials piled on the open ground and set on fire.Burn piles have spread uncontrolled fires. Burning material blown from the wind and small lightweight ignited embers lifted off the pile via convection can reach surrounding grass or buildings. As interior structures of the pile are consumed, the pile can shift and collapse, spreading the burn area. Burn piles often do not result in full combustion of waste and therefore produce particulate pollution.
Burn barrel
The burn barrel is a somewhat more controlled form of private waste incineration, containing the burning material inside a metal barrel, with a metal grating over the exhaust. The barrel prevents the spread of burning material in windy conditions, and as the combustibles are reduced they can only settle down into the barrel. The exhaust grating helps to prevent the spread of burning embers. Typically steel drums are used as burn barrels, with air vent holes cut or drilled around the base for air intake. Over time, the very high heat of incineration causes the metal to oxidize and rust, and eventually the barrel itself is consumed by the heat and must be replaced.The private burning of dry cellulosic/paper products is generally clean-burning, producing no visible smoke, but plastics in the household waste can cause private burning to create a public nuisance, generating acrid odors and fumes that make eyes burn and water. A two-layered design enables secondary combustion, reducing smoke. Most urban communities ban burn barrels and certain rural communities may have prohibitions on open burning, especially those home to many residents not familiar with this common rural practice.
in the United States, private rural household or farm waste incineration of small quantities was typically permitted so long as it is not a nuisance to others, does not pose a risk of fire such as in dry conditions, and the fire does not produce dense, noxious smoke. A handful of states, such as New York, Minnesota, and Wisconsin, have laws or regulations either banning or strictly regulating open burning due to health and nuisance effects. People intending to burn waste may be required to contact a state agency in advance to check current fire risk and conditions, and to alert officials of the controlled fire that will occur.
Moving grate
The typical incineration plant for municipal solid waste is a moving grate incinerator. The moving grate enables the movement of waste through the combustion chamber to be optimized to allow a more efficient and complete combustion. A single moving grate boiler can handle up to of waste per hour, and can operate 8,000 hours per year with only one scheduled stop for inspection and maintenance of about one month's duration. Moving grate incinerators are sometimes referred to as municipal solid waste incinerators.The waste is introduced by a waste crane through the "throat" at one end of the grate, from where it moves down over the descending grate to the ash pit in the other end. Here the ash is removed through a water lock.
Part of the combustion air is supplied through the grate from below. This air flow also has the purpose of cooling the grate itself. Cooling is important for the mechanical strength of the grate, and many moving grates are also water-cooled internally.
Secondary combustion air is supplied into the boiler at high speed through nozzles over the grate. It facilitates complete combustion of the flue gases by introducing turbulence for better mixing and by ensuring a surplus of oxygen. In multiple/stepped hearth incinerators, the secondary combustion air is introduced in a separate chamber downstream the primary combustion chamber.
According to the European Waste Incineration Directive, incineration plants must be designed to ensure that the flue gases reach a temperature of at least for 2 seconds in order to ensure proper breakdown of toxic organic substances. In order to comply with this at all times, it is required to install backup auxiliary burners, which are fired into the boiler in case the heating value of the waste becomes too low to reach this temperature alone.
The flue gases are then cooled in the superheaters, where the heat is transferred to steam, heating the steam to typically at a pressure of for the electricity generation in the turbine. At this point, the flue gas has a temperature of around, and is passed to the [|flue gas cleaning system].
Often, incineration plants consist of several separate 'boiler lines', so that waste can continue to be received at one boiler line while the others are undergoing maintenance, repair, or upgrading. In Scandinavia, scheduled maintenance is performed during summer, when the demand for district heating is low.
Fixed grate
The older and simpler kind of incinerator was a brick-lined cell with a fixed metal grate over a lower ash pit, with one opening in the top or side for loading and another opening in the side for removing incombustible solids called clinkers. Many small incinerators formerly found in apartment houses have now been replaced by waste compactors.Rotary-kiln
The rotary-kiln incinerator is used by municipalities and by large industrial plants. This design of incinerator has two chambers: a primary chamber and secondary chamber. The primary chamber in a rotary kiln incinerator consists of an inclined refractory lined cylindrical tube. The inner refractory lining serves as sacrificial layer to protect the kiln structure. This refractory layer needs to be replaced from time to time. Movement of the cylinder on its axis facilitates movement of waste. In the primary chamber, there is conversion of solid fraction to gases, through volatilization, destructive distillation and partial combustion reactions. The secondary chamber is necessary to complete gas phase combustion reactions.The clinkers spill out at the end of the cylinder. A tall flue-gas stack, fan, or steam jet supplies the needed draft. Ash drops through the grate, but many particles are carried along with the hot gases. The particles and any combustible gases may be combusted in an "afterburner".