Track geometry


Track geometry is concerned with the properties and relations of points, lines, curves, and surfaces in the three-dimensional positioning of railroad track. The term is also applied to measurements used in design, construction and maintenance of track. Track geometry involves standards, speed limits and other regulations in the areas of track gauge, alignment, elevation, curvature and track surface. Standards are usually separately expressed for horizontal and vertical layouts although track geometry is three-dimensional. Modern maintenance regimes increasingly use 3D laser scanning to capture these geometric parameters and assess structure gauge compliance without physical contact.

Layout

Horizontal layout

Horizontal layout is the track layout on the horizontal plane. This can be thought of as the plan view which is a view of a 3-dimensional track from the position above the track. In track geometry, the horizontal layout involves the layout of three main track types: tangent track, curved track, and track transition curve which connects between a tangent and a curved track. Curved track can also be categorized into three types. The first type is simple curve which has the same radius throughout that curved track. The second type is compound curve which comprises two or more simple curves of different radii that have the same direction of curvature. The third type is reverse curve which comprises two or more simple curves that has the opposite direction of curvature.
In Australia, there is a special definition for a bend which is a connection between two tangent tracks at almost 180 degrees without an intermediate curve. There is a set of speed limits for the bends separately from normal tangent track.

Vertical layout

Vertical layout is the track layout on the vertical plane. This can be thought of as the elevation view which is the side view of the track to show track elevation. In track geometry, the vertical layout involves concepts such as crosslevel, cant and gradient.

Track gauge

Track gauge or rail gauge is the distance between the inner sides of the heads of the two load bearing rails that make up a single railway line. Each country uses different gauges for different types of trains. However, the gauge is the basis of 60% of the world's railways.

Transverse elevation

Crosslevel

Crosslevel is the measurement of the difference in elevation between the top surface of the two rails at any point of railroad track. The two points are measured at by the right angles to the reference rail. Since the rail can slightly move up and down, the measurement should be done under load.
It is said to be zero crosslevel when there is no difference in elevation of both rails. It is said to be reverse crosslevel when the outside rail of curved track has lower elevation than the inside rail. Otherwise, the crosslevel is expressed in the unit of height.
The speed limits are governed by the crosslevel of the track. In tangent track, it is desired to have zero crosslevel. However, the deviation from zero can take place. Many regulations have specification related to speed limits of certain segment of the track based on the crosslevel.
For curved track, most countries use the term cant or superelevation to express the difference in elevation and related regulations.

Warp

Warp is the difference in crosslevel of any two points within the specific distance along the track. The warp parameter in the track geometry is used to specify the maximum in the crosslevel difference of the track in any segment.
Without the maximum warp parameter, the regulation on crosslevel alone may not be sufficient. Consider rails with a positive crosslevel followed by a negative crosslevel followed by a sequence of alternating positive and negative crosslevels. Although, all of those crosslevels are in permissible parameter, when operating a train along such track, the motion will be rocking left and right. Therefore, the maximum warp parameter is used to prevent the critical harmonic rock-off condition that may result in the trains rocking back and forth and derailing following wheel climb.
In North America, the specific distance used for measurement to ensure that the difference in crosslevel of the track is within the permissible warp parameter is 62 feet. The design warp is zero for both tangent and curved track. That means, ideally, the crosslevel should not change between any two points within 62 feet. There are some deviations to allow crosslevels along the track to change. Different levels of those deviations from the zero warp specify the speed limits.
The specification that focuses on the rate of change in crosslevels of curved track is contained within the area related to cant gradient.

Longitudinal elevation

Track gradient

The term track gradient is relative elevation of the two rails along the track. This can be expressed in the distance traveled horizontally for a rise of one unit, or in terms of an angle of inclination or a percentage difference in elevation for a given distance of the track.
The allowable gradients may be based on the ruling gradient which is the maximum gradient over which a tonnage train can be hauled with one locomotive. In some countries, momentum gradient which is a steeper but shorter gradient may be allowed. This is usually when a track gradient connects to a leveled tangent track long enough and with no signal between them such that a train can build momentum to push through a steeper grade than it can without the momentum gained on the leveled tangent track.
In curved track, there will be curve resistance to push the trains through the curve. The allowable gradients may be reduced on curves to compensate for the extra curve resistance. The gradient should be uniform along the track.

Vertical curve

Vertical curve is the curve in vertical layout to connect two track gradients together whether it is for changing from an upgrade to a downgrade, changing from a downgrade to an upgrade, changing in two levels of upgrades or changing in two levels of downgrades.
Some countries do not have specification on the exact geometry of vertical curves beyond general specification on vertical alignment. Australia has specification that the shape of vertical curves should be based on quadratic parabola but the length of a given vertical curve is calculated based on circular curve.

Curvature

Curvature refers to the amount by which a curve deviates from being a straight line. In the context of railway tracks, it is the measure of how much the track deviates from a straight path. It is essential in designing safe and efficient rail systems. In railways, curvature impacts the speed and safety of trains, as sharper curves require slower speeds to avoid derailment. The formula for curvature in a curve is typically defined as the inverse of the radius of the curve.
Curves are essential in railway tracks as they allow trains to navigate various geographical and urban obstacles that make straight routes impractical or impossible. Natural terrains, such as mountains, valleys, and rivers, require railways to adapt to existing landscapes, which is achieved through carefully designed curves. Additionally, in cities and populated areas, tracks must curve to fit within limited spaces or avoid buildings and other infrastructure. Curved tracks help railways maintain an efficient layout that minimizes land disruption and follows the natural or urban environment.
In most countries, the measurement of curvature of curved track is expressed in radius. The shorter the radius, the sharper the curve is. For sharper curves, the speed limits are lower to prevent an outward horizontal centrifugal force to overturn the trains by directing its weight toward the outside rail. Cant may be used to allow higher speeds over the same curve.
The curvature of railway tracks significantly affects train dynamics by influencing stability, safety, and performance.
  1. Centrifugal force and stability: When a train navigates a curve, centrifugal force acts outward, which can destabilize the train. To counter this, tracks are often tilted to balance the force.
  2. Wheel-rail interaction: Tight curves can cause higher lateral forces between wheels and rails, increasing wear and the risk of derailment.
  3. Speed limitations: Curves require speed restrictions to ensure the train remains stable and comfortable for passengers.
  4. Transition curves: Gradual transition curves, such as Euler spirals, are used to minimize sudden changes in curvature, reducing acceleration shocks and improving ride quality.
In North America, the measurement of curvature is expressed in degree of curvature. This is done by having a chord of connecting to two points on an arc of the reference rail, then drawing radii from the center to each of the chord's end points. The angle between the radii lines is the degree of curvature. The degree of curvature is inverse of radius. The larger the degree of curvature, the sharper the curve is. Expressing the curve in this way allows surveyors to use estimation and simpler tools in curve measurement. This can be done by using a string line to be a chord to connect the arc at the gauge side of the reference rail. Then at the midpoint of the string line, a measurement is taken from the string line to the gauge of the reference rail. The number of inches in that measurement is approximated to be the number of degrees of curvature.
Due to the limitation of how specific train equipment can make a turn at maximum speeds, there is a limitation of minimum curve radius to control the sharpness of all curves along a given route. Although most countries use radius for measurement of curvature, the term maximum degree of curvature is still used outside North America such as in India, but with the radius as the unit.