Fluorescent-lamp formats


Since their introduction as a commercial product in 1939, many different types of fluorescent lamp have been introduced. Systematic nomenclature identifies mass-market lamps as to overall shape, power rating, length, color, and other electrical and illuminating characteristics.

Tube designations

In the United States and Canada, lamps are typically identified by a code such as FxxTyy, where F is for fluorescent, and the first number indicates either the power in watts for bi-pin lamps, length in inches for single-pin and high-output lamps, and for circular bulbs, the diameter of the circular bulb. The T indicates that the shape of the bulb is tubular, and the last number is the diameter in eighths of an inch. Typical diameters are T12 or T38 for larger, often less efficient lamps, T8 or T26 for smaller and often energy-saving lamps, and T5 or T16 for very small lamps, which may even operate from a battery-powered device.
For T2–T12 and T17, the number indicates the tube diameter in inches, e.g. T2 → in and T17 → in. Whereas for T16 and T26–T38, the number indicates the approximate tube diameter in millimeters.

Reflectors

Some lamps have an internal opaque reflector. Coverage of the reflector ranges from 120° to 310° of the lamp's circumference.
Reflector lamps are used when light is only desired to be emitted in a single direction, or when an application requires the maximum amount of light. For example, these lamps can be used in tanning beds or in backlighting electronic displays. An internal reflector is more efficient than standard external reflectors. Another example is color matched aperture lights used in the food industry for robotic quality control inspection of cooked goods.
Aperture lamps have a clear break in the phosphor coating, typically of 30°, to concentrate light in one direction and provide higher brightness in the beam than can be achieved by uniform phosphor coatings. Aperture lamps include reflectors over the non-aperture area. Aperture lamps were commonly used in photocopiers in the 1960s and 1970s where a bank of fixed tubes was arranged to light up the image to be copied, but are rarely found nowadays. Aperture lamps can produce a concentrated beam of light suitable for edge-lit signs.

Single-pin lamps

Single-pin lamps operate on an instant start ballast in the United States and Canada or on a series choke without a starter in 220-240V countries.

High-output/very high output lamps

High-output lamps are brighter and are driven at a higher electric current. They have a recessed double contact base on each end, rather than a standard bi-pin base, which prevents them from being installed into the wrong fixture. Since about the early to mid-1950s to today, General Electric has developed and improved the Power Groove lamp. These lamps are recognizable by their large diameter and grooved tube shape.

Colors

Colors using a calcium halophosphate formulation are usually indicated by WW for warm white, W for white, CW for cool white, and D for the bluish daylight white.
Philips and Osram use numeric color codes for tri-phosphor and multi-phosphor colors. The first digit indicates the color rendering index of the lamp. If the first digit on a lamp says 8, then the CRI of that lamp will be approximately 85. The last two digits indicate the color temperature of the lamp in kelvins. For example, if the last two digits on a lamp say 41, that lamp's color temperature will be 4100 K, which is a common tri-phosphor cool white fluorescent lamp.
BL is used for ultraviolet lamps commonly used in bug zappers. BLB is used for blacklight-blue lamps employing a Wood's glass envelope to filter out most visible light, commonly used in nightclubs. Other non-standard designations apply for plant lights or grow lights.

Common tube ratings

This section lists the more common tube ratings for general lighting. Many more tube ratings exist, often country-specific. The Nominal Length may not exactly match any measured dimension of the tube. For some tube sizes, the nominal length is the required spacing between centers of the lighting fixtures to create a continuous run, so the tubes are a little shorter than the nominal length.
Tube diameter in Nominal lengthNominal power Lamp Code
T5 Miniature4F4T5
T5 Miniature6F6T5
T5 Miniature8F8T5
T5 Miniature13F13T5
T5/HE14F14T5
T5/HE21F21T5
T5/HE28F28T5
T5/HE35F35T5
T5/HO24F24T5/HO
T5/HO39F39T5/HO
T5/HO54F54T5/HO
T5/HO80F80T5/HO
T814F14T8
T815F15T8
T817F17T8
T82 ft 18N/A
T825F25T8
T83 ft 30F30T8
T832F32T8
T84 ft 36N/A
T840F40T8
T85 ft 58N/A
T870N/A
T8 single-pin38F72T8
T8 single-pin8 ft 51F96T8
T8 single-pin59F96T8
T8/HO44F48T8/HO
T8/HO55F60T8/HO
T8/HO65F72T8/HO
T8/HO86F96T8/HO
T1214F14T12
T1215F15T12
T1220F20T12
T1230F30T12
T1240F40T12
T1265N/A
T125 ft 80N/A
T1275N/A
T126 ft 85N/A
T12125N/A
T12 single-pin39F48T12
T12 single-pin55F72T12
T12 single-pin75F96T12
T12/HO60F48T12/HO
T12/HO75F60T12/HO
T12/HO85F72T12/HO
T12/HO110F96T12/HO
T12/VHO115F48T12/VHO
T12/VHO160F72T12/VHO
T12/VHO215F96T12/VHO

European energy-saving tubes

In the 1970s, Thorn Lighting introduced an energy-saving 8 ft retrofit tube in Europe. Designed to run on the existing 125 W series ballast but with a different gas fill and operating voltage, the tube operated at only 100 W. Increased efficiency meant that the tube produced only 9% lumen reduction for a 20% power reduction. This first energy-saving tube design remains a T12 tube even today. However, follow-on retrofit replacements for all the other original T12 tubes were T8, which helped with creating the required electrical characteristics and saving on the then new polyphosphor/triphosphor coatings, and these were even more efficient. Note that because these tubes were all designed as retrofit tubes to be fitted in T12 fittings running on series ballasts on 220–240 V supplies, they could not be used in 120 V mains countries with inherently different control gear designs.
TypeDiameter Nominal length Nominal power Notes
T81.0, 252, 0.618Retrofit replacement for 2 ft T12 20 W
T81.0, 254, 1.236Retrofit replacement for 4 ft T12 40 W
T81.0, 255, 1.558Retrofit replacement for 5 ft T12 65 W
T81.0, 256, 1.870Retrofit replacement for 6 ft T12 75 W
T121.5, 388, 2.4100Retrofit replacement for 8 ft T12 125 W

Around 1980, some new fluorescent fittings were designed to take only the newer, retrofit tubes. The earlier T12 halophosphate tubes still remained available as spares until 2012. They fit in older fittings and some modern fittings that employ twist lock lamp holders, even though the modern fittings were not electrically designed for them.

US energy-saving tubes

In the 1970s, 34-watt energy-saving F40T12 fluorescent lamps were intoroduced in the United States. In the 1980s, T8 32-watt lamps were introduced, but unlike the T8 tubes introduced in Europe, these T8s are not retrofits and require new matching ballasts to drive them. These ballasts were originally magnetic, but most today are electronic. The energy-saving T12 lamps are made to operate on ballasts designed for 40-watt F40T12 lamps, though some F40T12 ballasts are not be designed to operate these lamps, and can overheat if energy-saving lamps are used. Running an energy-saving T8 tube with a ballast for T12 will reduce lamp life and can increase energy consumption. Conversely, a T12 tube on a T8 ballast will usually draw too much power and so may burn out the ballast, unless it is within the range that particular ballast can compensate for. The tube type should always match the markings on the light fixture.
TypeDiameter Nominal length Nominal power Lamp CodeNotes
T50.625, 16449F49T5Retrofit replacement for 45.8 in T5HO 54 W
T81.0, 25425F32T8/25wRetrofit replacement for 4 ft T8 32 W
T81.0, 25428F28T8
F32T8/28w		Retrofit replacement for 4 ft T8 32 W
T81.0, 25430F32T8/ESRetrofit replacement for 4 ft T8 32 W
T81.0, 25217F17T8Ballast-swap replacement for 2 ft T12 20 W
T81.0, 25325F25T8Ballast-swap replacement for 3 ft T12 30 W
T81.0, 25432F32T8Ballast-swap replacement for 4 ft T12 40 W
T81.0, 25859F96T8Ballast-swap replacement for 8 ft T12 75 W single-pin
T121.5, 384"25"F40UTSLRetrofit replacement for 4 ft T12 40 W on underpowered residential-grade rapid start magnetic ballasts. These are F40CW lamps made with
lighter cathodes that can only handle a lower amount of power. They will function as a standard 40 W lamp on full-power ballasts, but may not last as long. These lamps are typically rated to last for 12,000
hours on a residential-grade ballast and only 6000 hours
on a commercial-grade one.
T121.5, 38432F40T12/ESPRetrofit replacement for 4 ft T12 40 W
T121.5, 38434F34T12
F40T12/ES		Retrofit replacement for 4 ft T12 40 W
T121.5, 38860F96T12/ESRetrofit replacement for 8 ft T12 75 W single-pin
T121.5, 38895F96T12/HO/ESRetrofit replacement for 8 ft T12 110 W high-output