Removable partial denture


A removable partial denture is a denture for a partially edentulous patient who desires to have replacement teeth for functional or aesthetic reasons and who cannot have a bridge for any reason, such as a lack of required teeth to serve as support for a bridge or financial limitations.
This type of prosthesis is referred to as a removable partial denture because patients can remove and reinsert it when required without professional help. Conversely, a "fixed" prosthesis can and should be removed only by a dental professional.
The aim of an RPD is to restore masticatory function, speech, appearance and other anatomical features.

Usage

RPD may be used when there is a lack of required teeth to serve as support for a bridge or financial limitations. A single-tooth RPD known as a "flipper tooth" may be used temporarily after a tooth is extracted, during the several months it takes to complete the placement of a dental implant and crown.
Advantages of using RPD include:
  • Reduced encroachment on existing teeth
  • Replacement of a greater number of missing teeth
  • Easily removed for cleaning and hygiene maintenance
  • Fairly simple to fix/replace the prosthesis if damaged
  • Modifications can be made to the prosthesis in some cases following additional tooth loss
Disadvantages of using RPD include:
  • Limited stability whilst in function
  • Significant coverage even in cases where few teeth require replacement in order to maximise retention
  • Visible components depending on teeth needing replacement
  • Potential risk to the health of remaining teeth due to plaque accumulation or trauma

    Classification

The patient's oral condition is categorized based on the remaining dentition in a classification first proposed by Dr. Edward Kennedy in 1925. His classification consisted of four general outlines for partially edentulous arches that can present within a patient, which then could be treated with an RPD. When there is an edentulous space that is outside of the four classifications, it is termed a modification space. The use of this classification allows for easier communication between dental professionals, allows for easily visualization of the arch, and distinguishes a tooth-borne or tissue-supported RPD.
  • Class I
  • Class II
  • Class III
  • Class IV
Kennedy Class I RPDs are fabricated for people who are missing some or all of their posterior teeth on both sides in a single arch, and there are no teeth posterior to the edentulous area. In other words, Class I RPDs clasp onto teeth that are more towards the front of the mouth, while replacing the missing posterior teeth on both sides with false denture teeth. The denture teeth are composed of either plastic or porcelain.
Class II RPDs are fabricated for people who are missing some or all of their posterior teeth on one side in a single arch, and there are no teeth behind the edentulous area. Thus, Class II RPDs clasp onto teeth that are more towards the front of the mouth, as well as on teeth that are more towards the back of the mouth of the side on which teeth are not missing, while replacing the missing more-back-of-the-mouth teeth on one side with false denture teeth.
Class III RPDs are fabricated for people who are missing some teeth in such a way that the edentulous area has teeth remaining both posterior and anterior to it. Unlike Class I and Class II RPDs which are both tooth-and-tissue-borne, Class III RPDs are strictly tooth-borne, which means they only clasp onto teeth and do not need to rest on the tissue for added support. This makes Class III RPDs exceedingly more secure as per the three rules of removable prostheses that will be mentioned later, namely: support, 'stability and retention.
However, if the edentulous area described in the previous paragraph crosses the anterior midline, the RPD is classified as a Class IV' RPD. By definition, a Kennedy Class IV RPD design will possess only one edentulous area.
Class I, II and III RPDs that have multiple edentulous areas in which replacement teeth are being placed are further classified with modification states that were defined by Oliver C. Applegate. Kennedy classification is governed by the most posterior edentulous area that is being restored. Thus if, for example, a maxillary arch is missing teeth #1, 3, 7-10 and 16, the RPD would be Kennedy Class III mod 1. It would not be Class I, because missing third molars are generally not restored in an RPD, and it would not be Class IV, because modification spaces are not allowed for Kennedy Class IV.
The results of a study conducted in Saudi Arabia, showed that the occurrence of Kennedy Class III partial edentulism was 67.2% in the maxillary arch and 64.1% in the mandibular arch. Followed by Class II in both maxillary and mandibular arch with an average of 16.3% in maxillary arch and 14.8% in the mandibular arch. Based on these results, class III has the highest prevalence in younger group of patient . Class I and class II have the highest incidence among older group of patients.

Design

Prior to designing partial dentures a complete examination is undertaken to assess the condition of remaining teeth. This may involve radiographs, sensibility testing or other assessments. From this examination and assessment of occlusion the designing of partial dentures can begin. Information from previous dentures can be very useful in deciding which features to keep the same and which features of the design to change – in the hope of making an improvement.

Stages of partial denture design

A systematic design process should be followed:
  • The teeth to be replaced must be decided.
  • The soft tissue to be replaced is then drawn.
  • The major connector is selected from a list of options.
  • Retentive features of the denture must be decided – these may include clasps, guide planes and indirect retention.
  • Supportive features are then decided – these prevent the denture sinking into the soft tissue; often the natural teeth can take some of the loading.
However, this is not always possible. Support may thus be tooth-borne, mucosal borne or a combination of tooth and mucosal borne.
  • The denture should where possible have features that withstand horizontal movement and the clasps should have appropriate reciprocation.
  • The denture base material and materials of the various components must be selected.
  • The hygiene of the prosthesis must be appropriate trying where possible to minimise the soft tissues coverage.
The design should be reviewed and simplified removing unnecessary components.
Once the partial denture has been designed, the shade and mould of the replacement teeth can be selected. Within the design process, modifications may be suggested to teeth. This may be undertaken to create occlusal space for rest seats or to create undercuts for the placement of clasps or to create guide planes for easier insertion and removal of the denture.

Components

Rather than lying entirely on the edentulous ridge like complete dentures, removable partial dentures possess clasps of cobalt-chrome or titanium metal or plastic that "clip" onto the remaining teeth, making the RPD more stable and retentive.
The parts of an RPD can be listed as follows :
  • Major connector
  • *Anterior-posterior palatal strap
  • *Single palatal strap
  • *U-shaped palatal connector
  • *Lingual bar
  • *Lingual plate
  • Minor connector
  • Direct retainer
  • Indirect retainer
  • *Physical retainer, while others consider them within the indirect retainer category
  • Base
  • '''Teeth'''

    Major connectors for upper teeth

There are many options for major connectors for removable upper partial dentures. The type of connector used will vary depending on the specific circumstances and the results of a comprehensive examination and discussion with the patient. Commonly used major connectors are outlined in the table below along with details of factors affecting the choice of using them.

Plate

Advantages of plates are that they are useful when several teeth are missing or there are multiple saddle. They also provide more retention, stability and support due to larger palatal coverage. Plates are useful when there are long distal extensions.
Disadvantages of plates are that they overs a lot of patients mouth so sometimes not well tolerated and also may affect phonetics. Plates can be problematic if there is a torus palatinus.

Palatal bar (Strap/Anterior-Posterior)

Advantages of these are their rigidity and minimal soft tissue coverage yet still having good resistance to deformation. A-P strap useful for Kennedy class I and II or if there is a torus. A-P strap gives greater distribution of stresses.
Disadvantages of these are that there is not much support due to less palatal coverage and also that is it bulky and so disliked by some patients.

U-shaped palatal bar (horseshoe connector)

Advantages of these are that they are useful in cases where we do not want to cover much of the palate e.g. if patient has a strong gag reflex, a large palatal torus or Kennedy class III.
Disadvantages of these are that they are flexible due to distal extensions which can have adverse effects on force transmission to abutment teeth. They can traumatic to the residual ridge.

Spoon denture

Advantages of these are that they are useful in small anterior saddles and are cheap to make.
Disadvantages of these are that they have large palatal coverage for a small saddle.

Palatal Strap/Bar (Single/Anterior, mid or Posterior)

Advantages of these are that single strap is useful for Kennedy class III and IV cases.
Disadvantage of these are that single strap requires careful placement if there is a torus palatinus. They are generally inappropriate for Kennedy Class 1 or 2.