Reference designator
A reference designator unambiguously identifies the location of a component within an electrical schematic or on a printed circuit board. The reference designator usually consists of one or two letters followed by a number, e.g. C3, D1, R4, U15. The number is sometimes followed by a letter, indicating that components are grouped or matched with each other, e.g. R17A, R17B. The IEEE 315 standard contains a list of Class Designation Letters to use for electrical and electronic assemblies. For example, the letter R is a reference prefix for the resistors of an assembly, C for capacitors, K for relays.
Industrial electrical installations often use reference designators according to IEC 81346.
History
IEEE 200-1975 or "Standard Reference Designations for Electrical and Electronics Parts and Equipments" is a standard that was used to define referencing naming systems for collections of electronic equipment. IEEE 200 was ratified in 1975. The IEEE renewed the standard in the 1990s, but withdrew it from active support shortly thereafter. This document also has an ANSI document number, ANSI Y32.16-1975.This standard codified information from, among other sources, a United States military standard MIL-STD-16 which dates back to at least the 1950s in American industry.
To replace IEEE 200-1975, ASME, a standards body for mechanical engineers, initiated the new standard ASME Y14.44-2008. This standard, along with IEEE 315-1975, provide the electrical designer with guidance on how to properly reference and annotate everything from a single circuit board to a collection of complete enclosures.
Definition
ASME Y14.44-2008 and IEEE 315-1975 define how to reference and annotate components of electronic devices.It breaks down a system into units, and then any number of sub-assemblies. The unit is the highest level of demarcation in a system and is always a numeral. Subsequent demarcation are called assemblies and always have the Class Letter "A" as a prefix following by a sequential number starting with 1. Any number of sub-assemblies may be defined until finally reaching the component. Note that IEEE 315-1975 defines separate class designation letters for separable assemblies and inseparable assemblies. Inseparable assemblies—i.e., "items which are ordinarily replaced as a single item of supply"—are typically treated as components in this referencing scheme.
Examples:
- 1A12A2R3 - Unit 1, Assembly 12, Sub-assembly 2, Resistor 3
- 1A12A2U3 - Unit 1, Assembly 12, Sub-assembly 2, Inseparable Assembly 3
Examples:
- 1A1A44J5 - Unit 1, Assembly 1, Sub-Assembly 44, Jack 5
- 1A1A45J333 - Unit 1, Assembly 1, Sub-Assembly 45, Jack 333
- 1A1W35 - In the assembly A1 is a cable called W35.
- 1A1W35P1
- 1A1W35P2
The construction of reference designators is covered by IEEE 200-1975/ANSI Y32.16-1975 and IEEE 315-1975.
Designators
The table below lists designators commonly used, and does not necessarily comply with standards. For modern use, designators are often simplified towards shorter designators, because it requires less space on silkscreens.| Designator | Component type | Modern use |
| A | Separable assembly or sub-assembly | |
| AT | Attenuator or isolator | |
| BR | Bridge rectifier | often changed to "D" for diode. |
| BT, BAT | Battery or battery holder | often shortened to "B". |
| C | Capacitor | |
| CB | Circuit breaker | |
| CN | Capacitor network | may be simplified to "C" for capacitor, some people use "CN" for connector. |
| D, CR | Diode, thyristor | "D" is preferred for various types of diodes. |
| DL | Delay line | |
| DN | Diode network | may be simplified to "D" for diode. |
| DS | Display, general light source, lamp, signal light | |
| F | Fuse | |
| FB | Ferrite bead | sometimes changed to "L" for inductor, though "E" was used in the currently inactive standard IEEE 315. |
| FD | Fiducial | |
| FL | Filter | |
| G, OSC | Generator or oscillator | |
| GL | Graphical logo | |
| GN | General network | |
| H | Hardware, e.g., screws, nuts, washers, also used for drilled holes | sometimes hardware is expanded to "HW", some people use "H" for header. |
| HY | Circulator or directional coupler | |
| IR | Infrared diode | often changed to "D" for diode |
| J | Jack connector | all types of connectors, including pin headers. |
| JP | Jumper | |
| K | Relay or contactor | |
| L | Inductor or coil or ferrite bead | |
| LD, LED | LED | often changed to "D" for diode. |
| LS, SPK | Loudspeaker or buzzer | |
| M | Motor | |
| MK, MIC | Microphone | |
| MP | Mechanical part | |
| OP | Opto-isolator | often changed to "U" for IC. |
| P | Plug connector | |
| PD | Photodiode | |
| Q | Transistor | |
| R | Resistor | |
| RN | Resistor network | sometimes simplified to "R" for resistor, or "N" for network. |
| RT | Thermistor | sometimes simplified to "R" for resistor. |
| RV | Varistor, variable resistor | |
| S | Switch | sometimes "SW" is used. |
| SA | Spark arrester | |
| T | Transistor | often changed to "Q", but sometimes "T" is used for bipolar transistors and "Q" for FETs. |
| TC | Thermocouple | |
| TP | Test point | |
| TR, T | Transformer | sometimes changed to "L" for inductor |
| TUN | Tuner | |
| U, IC | Integrated circuit | shorter "U" is preferred instead of "IC". |
| U#A, U#B... U#C | Integrated circuit | where # stands for number; this is used in multi-unit symbols just like "U", but with separate set of connections laid out in different places on the same schematics |
| V | Vacuum tube | |
| VR | Voltage regulator, or variable resistor | voltage regulators are often "U" for IC, pots and trimmers often "R" for resistor. |
| X | Socket connector for another item not P or J, paired with the letter symbol for that item | |
| X, XTAL, Y | Crystal, ceramic resonator, powered oscillator | |
| ZD | Zener diode | often changed to "D" for diode. |