Parabolic antenna


A parabolic antenna is an antenna that uses a parabolic reflector, a curved surface with the cross-sectional shape of a parabola, to direct the radio waves. The most common form is shaped like a dish and is popularly called a dish antenna or parabolic dish. The main advantage of a parabolic antenna is that it has high directivity. It functions similarly to a searchlight or flashlight reflector to direct radio waves in a narrow beam, or receive radio waves from one particular direction only. Parabolic antennas have some of the highest gains, meaning that they can produce the narrowest beamwidths, of any antenna type. In order to achieve narrow beamwidths, the parabolic reflector must be much larger than the wavelength of the radio waves used, so parabolic antennas are used in the high frequency part of the radio spectrum, at UHF and microwave frequencies, at which the wavelengths are small enough that conveniently sized reflectors can be used.
Parabolic antennas are used as high-gain antennas for point-to-point communications, in applications such as microwave relay links that carry telephone and television signals between nearby cities, wireless WAN/LAN links for data communications, satellite communications, and spacecraft communication antennas. They are also used in radio telescopes.
The other large use of parabolic antennas is for radar antennas, which need to transmit a narrow beam of radio waves to locate objects like ships, airplanes, and guided missiles. They are also often used for weather detection. With the advent of home satellite television receivers, parabolic antennas have become a common feature of the landscapes of modern countries.
The parabolic antenna was invented by German physicist Heinrich Hertz during his discovery of radio waves in 1887. He used cylindrical parabolic reflectors with spark-excited dipole antennas at their foci for both transmitting and receiving during his historic experiments.
Image:Parabola with focus and arbitrary line.svg|thumb|upright=1.3|Parabolic antennas are based on the geometrical property of the paraboloid that the paths FP1Q1, FP2Q2, FP3Q3 are all the same length. Thus, a spherical wavefront emitted by a feed antenna at the dish's focus F will be reflected into an outgoing plane wave L travelling parallel to the dish's axis VF.

Design

The operating principle of a parabolic antenna is that a point source of radio waves at the focal point in front of a paraboloidal reflector of conductive material will be reflected into a collimated plane wave beam along the axis of the reflector. Conversely, an incoming plane wave parallel to the axis will be focused to a point at the focal point.
A typical parabolic antenna consists of a metal parabolic reflector with a small feed antenna suspended in front of the reflector at its focus, pointed back toward the reflector. The reflector is a metallic surface formed into a paraboloid of revolution and usually truncated in a circular rim that forms the diameter of the antenna. In a transmitting antenna, radio frequency current from a transmitter is supplied through a transmission line cable to the feed antenna, which converts it into radio waves. The radio waves are emitted back toward the dish by the feed antenna and reflect off the dish into a parallel beam. In a receiving antenna the incoming radio waves bounce off the dish and are focused to a point at the feed antenna, which converts them into electric currents which travel through a transmission line to the radio receiver.

Parabolic reflector

The reflector can be constructed from sheet metal, a metal screen, or a wire grill, and can be either a circular dish or various other shapes to create different beam shapes. A metal screen reflects radio waves as effectively as a solid metal surface if its holes are smaller than one-tenth of a wavelength, so screen reflectors are often used to reduce weight and wind loads on the dish. To achieve the maximum gain, the shape of the dish needs to be accurate within a small fraction of a wavelength, around one sixteenth wavelength, to ensure the waves from different parts of the antenna arrive at the focus in phase. Large dishes often require a supporting truss structure behind them to provide the required stiffness.
A reflector made of a grill of parallel wires or bars oriented in one direction acts as a polarizing filter as well as a reflector. It only reflects linearly polarized radio waves, with the electric field parallel to the grill elements. This type is often used in radar antennas. Combined with a linearly polarized feed horn, it helps filter out noise in the receiver and reduces false returns.
A shiny metal parabolic reflector can also focus the sun's rays. Since most dishes could concentrate enough solar energy on the feed structure to severely overheat it if they happened to be pointed at the sun, solid reflectors are always given a coat of flat paint.

Feed antenna

The feed antenna at the reflector's focus is typically a low-gain type, such as a half-wave dipole or a small horn antenna called a feed horn. In more complex designs, such as the Cassegrain and Gregorian, a secondary reflector is used to direct the energy into the parabolic reflector from a feed antenna located away from the primary focal point. The feed antenna is connected to the associated radio-frequency transmitting or receiving equipment by means of a coaxial cable transmission line or waveguide.
At the microwave frequencies used in many parabolic antennas, waveguide is required to conduct the microwaves between the feed antenna and transmitter or receiver. Because of the high cost of waveguide runs, in many parabolic antennas the RF front end electronics of the receiver is located at the feed antenna, and the received signal is converted to a lower intermediate frequency so it can be conducted to the receiver through cheaper coaxial cable. This is called a low-noise block downconverter. Similarly, in transmitting dishes, the microwave transmitter may be located at the feed point.
An advantage of parabolic antennas is that most of the structure of the antenna is nonresonant, so it can function over a wide range of frequencies. All that is necessary to change the frequency of operation is to replace the feed antenna with one that operates at the desired frequency. Some parabolic antennas transmit or receive at multiple frequencies by having several feed antennas mounted at the focal point, close together.

Types

Parabolic antennas are distinguished by their shapes:
  • Paraboloidal or dish – The reflector is shaped like a paraboloid truncated with a circular rim. This is the most common type. It radiates a narrow pencil-shaped beam along the axis of the dish.
  • * Shrouded dish – Sometimes a cylindrical metal shield is attached to the rim of the dish. The shroud shields the antenna from radiation from angles outside the main beam axis, reducing the sidelobes. It is sometimes used to prevent interference in terrestrial microwave links, where several antennas using the same frequency are located close together. The shroud is coated inside with microwave absorbent material. Shrouds can reduce back lobe radiation by 10 dB.
  • Cylindrical – The reflector is curved in only one direction and flat in the other. The radio waves come to a focus not at a point but along a line. The feed is sometimes a dipole antenna located along the focal line. Cylindrical parabolic antennas radiate a fan-shaped beam, narrow in the curved dimension, and wide in the uncurved dimension. The curved ends of the reflector are sometimes capped by flat plates, to prevent radiation out the ends, and this is called a pillbox antenna or cheese antenna.
  • Shaped-beam antennas – Modern reflector antennas can be designed to produce a beam or beams of a particular shape, rather than just the narrow "pencil" or "fan" beams of the simple dish and cylindrical antennas mentioned above. Two techniques are used, often in combination, to control the shape of the beam:
Image:Stacked beam2.jpg|thumb|Array of multiple feed horns on a German airport surveillance radar antenna to control the elevation angle of the beam
Parabolic antennas are also classified by the type of feed, that is, how the radio waves are supplied to the antenna:
  • Axial, prime focus, or front feed – This is the most common type of feed, with the feed antenna located in front of the dish at the focus, on the beam axis, pointed back toward the dish. A disadvantage of this type is that the feed and its supports block some of the beam, which limits the aperture efficiency to only 55–60%.
  • Off-axis or offset feed – The reflector is an asymmetrical segment of a paraboloid, so the focus, and the feed antenna, are located to one side of the dish. The purpose of this design is to move the feed structure out of the beam path, so it does not block the beam. It is widely used in home satellite television dishes, which are small enough that the feed structure would otherwise block a significant percentage of the signal. Offset feed can also be used in multiple reflector designs such as the Cassegrain and Gregorian, below.
  • Cassegrain – In a Cassegrain antenna, the feed is located on or behind the dish, and radiates forward, illuminating a convex hyperboloidal secondary reflector at the focus of the dish. The radio waves from the feed reflect off the secondary reflector to the dish, which reflects them forward again, forming the outgoing beam. An advantage of this configuration is that the feed, with its waveguides and "front end" electronics does not have to be suspended in front of the dish, so it is used for antennas with complicated or bulky feeds, such as large satellite communication antennas and radio telescopes. Aperture efficiency is on the order of 65–70%.
  • Gregorian – Similar to the Cassegrain design except that the secondary reflector is concave in shape. Aperture efficiency over 70% can be achieved.