Decompression practice
To prevent or minimize decompression sickness, divers must properly plan, conduct, and monitor decompression. Divers follow a decompression model to allow the release of excess inert gases dissolved in their body tissues at acceptable risk, which accumulated as a result of breathing at ambient pressures greater than surface atmospheric pressure. Decompression models take into account variables such as depth and time of dive, breathing gasses, altitude, and equipment to develop appropriate procedures for safe ascent.
Decompression may be continuous or staged, where the ascent is interrupted by stops at regular depth intervals, but the entire ascent is part of the decompression, and ascent rate can be critical to harmless elimination of inert gas. What is commonly known as no-decompression diving, or more accurately no-stop decompression, relies on limiting ascent rate for avoidance of excessive bubble formation. Staged decompression may include deep stops depending on the theoretical model used for calculating the ascent schedule. Omission of decompression theoretically required for a dive profile exposes the diver to significantly higher risk of symptomatic decompression sickness, and in severe cases, serious injury or death. The risk is related to the severity of exposure and the level of supersaturation of tissues in the diver. Procedures for emergency management of omitted decompression and symptomatic decompression sickness have been published. These procedures are generally effective, but vary in effectiveness from case to case.
The procedures used for decompression depend on the mode of diving, the available equipment, the site and environment, and the actual dive profile. Standardized procedures have been developed which provide an acceptable level of risk in the circumstances for which they are appropriate. Different sets of procedures are used by commercial, military, scientific and recreational divers, though there is considerable overlap where similar equipment is used, and some concepts are common to all decompression procedures. In particular, all types of surface oriented diving benefited significantly from the acceptance of personal dive computers in the 1990s, which facilitated decompression practice and allowed more complex dive profiles at acceptable levels of risk.
Decompression
Decompression in the context of diving derives from the reduction in ambient pressure experienced by the diver during the ascent at the end of a dive or hyperbaric exposure and refers to both the reduction in pressure and the process of allowing dissolved inert gases to be eliminated from the tissues during this reduction in pressure. When a diver descends in the water column the ambient pressure rises. Breathing gas is supplied at the same pressure as the surrounding water, and some of this gas dissolves into the diver's blood and other fluids. Inert gas continues to be taken up until the gas dissolved in the diver is in a state of equilibrium with the breathing gas in the diver's lungs,, or the diver moves up in the water column and reduces the ambient pressure of the breathing gas until the inert gases dissolved in the tissues are at a higher concentration than the equilibrium state, and start diffusing out again. Dissolved inert gases such as nitrogen or helium can form bubbles in the blood and tissues of the diver if the partial pressures of the dissolved gases in the diver gets too high above the ambient pressure. These bubbles and products of injury caused by the bubbles can cause damage to tissues known as decompression sickness, or "the bends". The immediate goal of controlled decompression is to avoid development of symptoms of bubble formation in the tissues of the diver, and the long-term goal is to also avoid complications due to sub-clinical decompression injury.A diver who exceeds the no-decompression limit for a decompression algorithm or table has a theoretical tissue gas loading which is considered likely to cause symptomatic bubble formation unless the ascent follows a decompression schedule, and is said to have a decompression obligation.
Common procedures
Descent rate
Descent rate is generally allowed for in decompression planning by assuming a maximum descent rate specified in the instructions for the use of the tables, but it is not critical. Descent slower than the nominal rate reduces useful bottom time, but has no other adverse effect. Descent faster than the specified maximum will expose the diver to greater ingassing rate earlier in the dive, and the bottom time must be reduced accordingly. In the case of real-time monitoring by dive computer, descent rate is not specified, as the consequences are automatically accounted for by the programmed algorithm.Bottom time
Bottom time is the time spent at depth before starting the ascent. Bottom time used for decompression planning may be defined differently depending on the tables or algorithm used. It may include descent time, but not in all cases. It is important to check how bottom time is defined for the tables before they are used. For example, tables using Bühlmann's algorithm define bottom time as the elapsed time between leaving the surface and the start of the final ascent at 10 metres per minute, and if the ascent rate is slower, then the excess of the ascent time to the first required decompression stop needs to be considered part of the bottom time for the tables to remain safe.Ascent rate
The ascent is an important part of the process of decompression, as this is the time when reduction of ambient pressure occurs, and it is of critical importance to safe decompression that the ascent rate is compatible with safe elimination of inert gas from the diver's tissues. Ascent rate must be limited to prevent supersaturation of tissues to the extent that unacceptable bubble development occurs. This is usually done by specifying a maximum ascent rate compatible with the decompression model chosen. This will be specified in the decompression tables or the user manual for the decompression software or personal decompression computer. The instructions will usually include contingency procedures for deviation from the specified rate, both for delays and exceeding the recommended rate. Failure to comply with these specifications will generally increase the risk of decompression sickness.Typically maximum ascent rates are in the order of per minute for dives deeper than. Some dive computers have variable maximum ascent rates, depending on depth. Ascent rates slower than the recommended standard for the algorithm will generally be treated by a computer as part of a multilevel dive profile and the decompression requirement adjusted accordingly. Faster ascent rates will elicit a warning and additional decompression stop time to compensate.
Monitoring decompression status
Decompression status is the assumed gas loading of the diver's tissues, based on the chosen decompression model, and either calculated by a dive computer or estimated from dive tables by the diver or diving supervisor, and an indication of the decompression stress that will be incurred by decompressing to a lower ambient pressure.The decompression status of the diver must be known before starting the ascent, so that an appropriate decompression schedule can be followed to avoid an excessive risk of decompression sickness. Scuba divers are responsible for monitoring their own decompression status, as they are the only ones to have access to the necessary information. Surface supplied divers depth profile and elapsed time can be monitored by the surface team, and the responsibility for keeping track of the diver's decompression status is generally part of the supervisor's job.
The supervisor will generally assess decompression status based on dive tables, maximum depth and elapsed bottom time of the dive, though multi-level calculations are possible. Depth is measured at the gas panel by pneumofathometer, which can be done at any time without distracting the diver from their activity. The instrument does not record a depth profile, and requires intermittent action by the panel operator to measure and record the current depth. Elapsed dive time and bottom time are easily monitored using a stopwatch. Worksheets for monitoring the dive profile are available, and include space for listing the ascent profile including decompression stop depths, time of arrival, and stop time. If repetitive dives are involved, residual nitrogen status is also calculated and recorded, and used to determine the decompression schedule. A surface supplied diver may also carry a bottom timer or decompression computer to provide an accurate record of the actual dive profile, and the computer output may be taken into account when deciding on the ascent profile. The dive profile recorded by a dive computer would be valuable evidence in the event of an accident investigation.
Scuba divers can monitor decompression status by using maximum depth and elapsed time in the same way, and can use those to either select from a previously compiled set of surfacing schedules, or identify the recommended profile from a waterproof dive table taken along on the dive. It is possible to calculate a decompression schedule for a using this system, but the possibility of error is significant due to the skill and attention required, and the table format, which can be misread under task loading or in poor visibility. The current trend is towards the use of dive computers to calculate the in real time, using depth and time data automatically input into the processing unit, and continuously displayed on the output screen. Dive computers have become quite reliable, but can fail in service for a variety of reasons, and it is prudent to have a backup system available to estimate a reasonable safe ascent if the computer fails. This can be a backup computer, a written schedule with watch and depth gauge, or the dive buddy's computer if they have a reasonably similar dive profile. If only no-stop diving is done, and the diver makes sure that the no-stop limit is not exceeded, a computer failure can be managed at acceptable risk by starting an immediate direct ascent to the surface at an appropriate ascent rate.