Turning


Turning is a machining process in which a cutting tool is held nearly stationary to cut a rotating workpiece. The cutting tool can be slowly moved back-and-forth, and in-and-out to cut cylindrical shapes, and flat surfaces on the workpiece. Turning is usually done with a lathe.
Usually the term "turning" is used for cutting external surfaces, and "boring" for internal surfaces, or holes. Thus the phrase "turning and boring" categorizes the larger family of processes known as lathing. Additionally, "facing" is cutting the ends of the workpiece, to create flat faces.
Turning is typically done with either a manual lathe, or a computer numerical control lathe. With a manual lathe, an operator turns cranks to move the cutting tool. On a CNC lathe, the cutting tool is moved by a computer, controlling electric motors to follow a pre-programmed path. Early manual lathes could be used to produce complex geometric figures, even the platonic solids; though this is now usually done with CNC machines.
Different turning processes are typically carried out on a lathe, such as straight turning, taper turning, profiling or external grooving. Those types of turning processes can produce various shapes of materials such as straight, conical, curved, or grooved workpieces.
In general, turning uses simple single-point cutting tools.
The waste metal cut off of the workpiece from turning operations is known as chips in North America, or swarf in Britain. In some areas they may be known as turnings.
A component that is made by turning is often called a turned part.

Turning operations

; Turning
; Boring
;Drilling
;
; Grooving
; Parting
; Knurling
;Threading
;Polygonal turning

Lathes

Turning is usually performed on a lathe, which range in size from tabletop machines suitable for jewelry, to building-sized machines for manufacturing ship propeller shafts.

Workholding methods

;Chuck: Chucks grip a workpiece with movable jaws. They are less accurate than collets, but can hold a wider range of workpiece sizes.
;Collet: Collets grip a workpiece by deforming around it. They grip over a larger surface than chucks, which puts less pressure on the workpiece, and center the workpiece better. Each collet has only a narrow range of workpiece diameters that it can deform enough to hold, so large sets of different collets are needed.
;Faceplate: A faceplate is a plate that a workpiece is attached to, often with clamps or t-slot nuts. It is often used with a drive dog and mandrel. It can hold even more irregularly shaped workpieces than a chuck.
;Centers: Centers are pointed cones, which support either a hollow tube workpiece, or a workpiece with holes drilled in its ends. Workpieces are ofter driven by a "dog".
;Drive center: A drive center is a center which grips the workpiece strongly enough to drive it without the use of a dog. They often use hydraulic or spring-loaded teeth that bite into the end of workpieces. When supporting a workpiece only with centers, the entire outside of the workpiece may be machined in one setup.

Tooling

Turning tooling usually cuts with a single point, as opposed to a drill bit or end mill which cut with several sharp edges. The angles around the sharp point are important, such as rake angle, side rake angle, cutting-edge angle, and relief angle. Additionally, the cutting point may have a nose radius which creates radii when cutting corners in the workpiece and extends the life of the tool tip, but increases machining forces.
The tool bit is held with a rigid tool holder during operation. CNC machines are typically able to switch tools automatically.

Dynamics of turning

Forces

Significant forces are required for turning operation, and must be accounted for in the design and selection of the machine tools, the workpiece holding, and any additional supports. A setup that is not strong enough may allow the workpiece to break free during operation, ruining the part being made, and endangering the operator. A setup that is not rigid enough will deform during operation, and create chatter when cutting, creating an undesirable surface finish, and inaccurate dimensions.
There are three principal forces in turning:
  • The cutting or tangential force acts downward on the tool tip and upwards on the workpiece upward. This is the force required to cut chips off of the workpiece. The force required to cut the material is called the specific cutting force, and depends on the material, cut depth, cut speed, and lubrication.
  • The axial or feed force acts in the longitudinal, or feed direction. This is the force necessary to feed the tool along the rotational axis of the workpiece.
  • The radial or thrust force acts in the radial direction and tends to push the tool out of the workpiece.

Speeds and feeds

Speeds and feeds refer to the rotational speed that the workpiece is rotated at, and the feed speed that the tool is moved at. They are chosen based on the workpiece material, cutter material, setup rigidity, machine tool rigidity, spindle power, and whether coolant is used.
The rotational speed is measured in revolutions per minute.
The feed rate is the distance that the tool is fed into the workpiece per workpiece revolution. It is measured either as millimeters per revolution, or as inches per revolution.