Hard disk drive failure


A hard disk drive failure occurs when a hard disk drive malfunctions and the stored information cannot be accessed with a properly configured computer.
A hard disk failure may occur in the course of normal operation, or due to an external factor such as exposure to fire or water or high magnetic fields, or suffering a sharp impact or environmental contamination, which can lead to a head crash.
The stored information on a hard drive may also be rendered inaccessible as a result of data corruption, disruption or destruction of the hard drive's master boot record, or by malware deliberately destroying the disk's contents.

Causes

There are a number of causes for hard drives to fail including: human error, hardware failure, firmware corruption, media damage, heat, water damage, power issues and mishaps. Drive manufacturers typically specify a mean time between failures or an annualized failure rate which are population statistics that can't predict the behavior of an individual unit. These are calculated by constantly running samples of the drive for a short period of time, analyzing the resultant wear and tear upon the physical components of the drive, and extrapolating to provide a reasonable estimate of its lifespan. Hard disk drive failures tend to follow the concept of the bathtub curve. Drives typically fail within a short time if there is a defect present from manufacturing. If a drive proves reliable for a period of a few months after installation, the drive has a significantly greater chance of remaining reliable. Therefore, even if a drive is subjected to several years of heavy daily use, it may not show any notable signs of wear unless closely inspected. On the other hand, a drive can fail at any time in many different situations.
The most notorious cause of drive failure is a head crash, where the internal read-and-write head of the device, usually just hovering above the surface, touches a platter, or scratches the magnetic data-storage surface. A head crash usually incurs severe data loss, and data recovery attempts may cause further damage if not done by a specialist with proper equipment. Drive platters are coated with an extremely thin layer of non-electrostatic lubricant, so that the read-and-write head will likely simply glance off the surface of the platter should a collision occur. However, this head hovers mere nanometers from the platter's surface which makes a collision an acknowledged risk.
Another cause of failure is a faulty air filter. The air filters on today's drives equalize the atmospheric pressure and moisture between the drive enclosure and its outside environment. If the filter fails to capture a dust particle, the particle can land on the platter, causing a head crash if the head happens to sweep over it. After a head crash, particles from the damaged platter and head media can cause one or more bad sectors. These, in addition to platter damage, will quickly render a drive useless.
A drive also includes controller electronics, which occasionally fail. In such cases, it may be possible to recover all data by replacing the controller board.

Signs of drive failure

Failure of a hard disk drive can be catastrophic or gradual. The former typically presents as a drive that can no longer be detected by CMOS setup, or that fails to pass BIOS POST so that the operating system never sees it. Gradual hard-drive failure can be harder to diagnose, because its symptoms, such as corrupted data and slowing down of the PC, can be caused by many other computer issues, such as malware. A rising number of bad sectors can be a sign of a failing hard drive, but because the hard drive automatically adds them to its own growth defect table, they may not become evident to utilities such as ScanDisk unless the utility can catch them before the hard drive's defect management system does, or the backup sectors held in reserve by the internal hard-drive defect management system run out. A cyclical repetitive pattern of seek activity such as rapid or slower seek-to-end noises can be indicative of hard drive problems.

Landing zones and load/unload technology

During normal operation, heads in HDDs fly above the data recorded on the disks. Modern HDDs prevent power interruptions or other malfunctions from landing its heads in the data zone by either physically moving the heads to a special landing zone on the platters that is not used for data storage, or by physically locking the heads in a suspended position raised off the platters. Some early PC HDDs did not park the heads automatically when power was prematurely disconnected and the heads would land on data. In some other early units the user would run a program to manually park the heads.

Landing zones

A landing zone is an area of the platter usually near its inner diameter, where no data is stored. This area is called the Contact Start/Stop zone, or the landing zone. Disks are designed such that either a spring or, more recently, rotational inertia in the platters is used to park the heads in the case of unexpected power loss. In this case, the spindle motor temporarily acts as a generator, providing power to the actuator.
Spring tension from the head mounting constantly pushes the heads towards the platter. While the disk is spinning, the heads are supported by an air bearing and experience no physical contact or wear. In CSS drives the sliders carrying the head sensors are designed to survive a number of landings and takeoffs from the media surface, though wear and tear on these microscopic components eventually takes its toll. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear: when a disk is younger and has had fewer start-stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage disk. For example, the Seagate Barracuda 7200.10 series of desktop hard disk drives are rated to 50,000 start-stop cycles; in other words, no failures attributed to the head-platter interface were seen before at least 50,000 start-stop cycles during testing.
Around 1995 IBM pioneered a technology where a landing zone on the disk is made by a precision laser process'' producing an array of smooth nanometer-scale "bumps" in a landing zone, thus vastly improving stiction and wear performance. This technology is still in use today, predominantly in older/refurbished hard drives and more recent lower-capacity Seagate desktop drives from the early 2010s onwards in cheaper models including the 7200.12 series, 7200.14 series models that are 500GB and under and was even still used in the 16th generation in one model introduced in 2016 being the one of the last known hard drives to use CSS, but had already been phased out in all 2.5" drives, as well as higher-capacity desktop, NAS, and enterprise drives since around 2012 in favor of load/unload ramps. Western Digital and Toshiba also fully phased out CSS in all their hard drives including the cheapest models. Some early adopters included IBM and Hitachi. In general, CSS technology can be prone to increased stiction, e.g. as a consequence of increased humidity. Excessive stiction can cause physical damage to the platter and slider or spindle motor. Though this older technology is still often found in older used/refurbished units that are still quite good for budget conscious users.

Unloading

Load/unload technology relies on the heads being lifted off the platters into a safe location, thus eliminating the risks of wear and stiction altogether. The first HDD RAMAC and most early disk drives used complex mechanisms to load and unload the heads. Nearly all modern HDDs use ramp loading, first introduced by Memorex in 1967, to load/unload onto plastic "ramps" near the outer disk edge. Laptop drives adopted this early due to the need for increased shock resistance, and then ultimately it was adopted on most desktop drives around the late 2000s-early2010s when adoption accelerated.
Addressing shock robustness, IBM also created a technology for their ThinkPad line of laptop computers called the Active Protection System. When a sudden, sharp movement is detected by the built-in accelerometer in the ThinkPad, internal hard disk heads automatically unload themselves to reduce the risk of any potential data loss or scratch defects. Apple later also utilized this technology in their PowerBook, iBook, MacBook Pro, and MacBook line, known as the Sudden Motion Sensor. Sony, HP with their HP 3D DriveGuard, and Toshiba have released similar technology in their notebook computers.

Modes of failure

Hard drives may fail in a number of ways. Failure may be immediate and total, progressive, or limited. Data may be totally destroyed, or partially or totally recoverable.
Earlier drives had a tendency toward developing bad sectors with use and wear; these bad sectors could be "mapped out" so they were not used and did not affect operation of a drive, and this was considered normal unless many bad sectors developed in a short period of time. Some early drives even had a table attached to a drive's case on which bad sectors were to be listed as they appeared. Later drives map out bad sectors automatically, in a way invisible to the user; a drive with remapped sectors may continue to be used, though performance may decrease as the drive must physically move the heads to the remapped sector. Statistics and logs available through S.M.A.R.T. provide information about the remapping. In modern HDDs, each drive ships with zero user-visible bad sectors, and any bad/reallocated sectors may predict the impending failure of a drive.
Other failures, which may be either progressive or limited, are usually considered to be a reason to replace a drive; the value of data potentially at risk usually far outweighs the cost saved by continuing to use a drive which may be failing. Repeated but recoverable read or write errors, unusual noises, excessive and unusual heating, and other abnormalities, are warning signs.
  • Head crash: a head may contact the rotating platter due to mechanical shock or other reason. At best this will cause irreversible damage and data loss where contact was made. In the worst case the debris scraped off the damaged area may contaminate all heads and platters, and destroy all data on all platters. If damage is initially only partial, continued rotation of the drive may extend the damage until it is total.
  • Bad sectors: some magnetic sectors may become faulty without rendering the whole drive unusable. This may be a limited occurrence or a sign of imminent failure. A drive that has any reallocated sectors at all has a significantly increased chance of failing soon.
  • Stiction: after a time the head may not "take off" when started up as it tends to stick to the platter, a phenomenon known as stiction. This is usually due to unsuitable lubrication properties of the platter surface, a design or manufacturing defect rather than wear. This occasionally happened with some designs until the early 1990s.
  • Circuit failure: components of the electronic circuitry may fail making the drive inoperable, often due to electrostatic discharge or user error.
  • Bearing and motor failure: electric motors may fail or burn out, and bearings may wear enough to prevent proper operation. Since modern drives use fluid dynamic bearings, this is a relatively uncommon reason for modern hard drive failure.
  • Miscellaneous mechanical failures: parts, particularly moving parts, of any mechanism can break or fail, preventing normal operation, with possible further damage caused by fragments.