Engineering fit
Engineering fits are generally used as part of geometric dimensioning and tolerancing when a part or assembly is designed. In engineering terms, the "fit" is the clearance between two mating parts, and the size of this clearance determines whether the parts can, at one end of the spectrum, move or rotate independently from each other or, at the other end, are temporarily or permanently joined. Engineering fits are generally described as a "shaft and hole" pairing, but are not necessarily limited to just round components. ISO is the internationally accepted standard for defining engineering fits, but ANSI is often still used in North America.
ISO and ANSI both group fits into three categories: clearance, location or transition, and interference. Within each category are several codes to define the size limits of the hole or shaft – the combination of which determines the type of fit. A fit is usually selected at the design stage according to whether the mating parts need to be accurately located, free to slide or rotate, separated easily, or resist separation. Cost is also a major factor in selecting a fit, as more accurate fits will be more expensive to produce, and tighter fits will be more expensive to assemble.
Methods of producing work to the required tolerances to achieve a desired fit range from casting, forging and drilling for the widest tolerances through broaching, reaming, milling and turning to lapping and honing at the tightest tolerances.
ISO system of limits and fits
Overview
The International Organization for Standardization system splits the three main categories into several individual fits based on the allowable limits for hole and shaft size. Each fit is allocated a code, made up of a number and a letter, which is used on engineering drawings in place of upper & lower size limits to reduce clutter in detailed areas.Hole and shaft basis
A fit is either specified as shaft-basis or hole-basis, depending on which part has its size controlled to determine the fit. In a hole-basis system, the size of the hole remains constant and the diameter of the shaft is varied to determine the fit; conversely, in a shaft-basis system the size of shaft remains constant and the hole diameter is varied to determine the fit.The ISO system uses an alpha-numeric code to illustrate the tolerance ranges for the fit, with the upper-case representing the hole tolerance and lower-case representing the shaft. For example, in H7/h6 H7 represents the tolerance range of the hole and h6 represents the tolerance range of the shaft. These codes can be used by machinists or engineers to quickly identify the upper and lower size limits for either the hole or shaft. The potential range of clearance or interference can be found by subtracting the smallest shaft diameter from the largest hole, and largest shaft from the smallest hole.
Types of fit
The three types of fit are:- Clearance: The hole is larger than the shaft, enabling the two parts to slide and / or rotate when assembled, e.g. piston and valves
- Location / transition: The hole is fractionally smaller than the shaft and mild force is required to assemble / disassemble, e.g. Shaft key
- Interference: The hole is smaller than the shaft and high force and / or heat is required to assemble / disassemble, e.g. Bearing bush
Clearance fits
For example, using an H8/f7 close-running fit on a 50mm diameter:- H8 tolerance range = +0.000mm to +0.039mm
- f7 tolerance range = −0.050mm to −0.025mm
- Potential clearance will be between +0.025mm and +0.089mm
Transition fits
For example, using an H7/k6 similar fit on a 50mm diameter:- H7 tolerance range = +0.000mm to +0.025mm
- k6 tolerance range = +0.002mm to +0.018mm
- Potential clearance / interference will be between +0.023mm and −0.018mm
Interference fits
For example, using an H7/p6 press fit on a 50mm diameter:- H7 tolerance range = +0.000mm to +0.025mm
- p6 tolerance range = +0.042mm to +0.026mm
- Potential interference will be between −0.001mm and −0.042mm.
Useful tolerances
Common tolerances for sizes ranging from 0 to 120 mmANSI fit classes (US only)
Interference fits
Interference fits, also known as press fits or friction fits, are fastenings between two parts in which the inner component is larger than the outer component. Achieving an interference fit requires applying force during assembly. After the parts are joined, the mating surfaces will feel pressure due to friction, and deformation of the completed assembly will be observed.Force fits
Force fits are designed to maintain a controlled pressure between mating parts, and are used where forces or torques are being transmitted through the joining point. Like interference fits, force fits are achieved by applying a force during component assembly.FN 1 to FN 5
Shrink fits
Shrink fits serve the same purpose as force fits, but are achieved by heating one member to expand it while the other remains cool. The parts can then be easily put together with little applied force, but after cooling and contraction, the same dimensional interference exists as for a force fit. Like force fits, shrink fits range from FN 1 to FN 5.Location fits
Location fits are for parts that do not normally move relative to each other.Location interference fit
LN 1 to LN 3Location transition fit
LT 1 to LT 6Location fit is for have comparatively better fit than slide fit.