Boiler explosion
A boiler explosion is a catastrophic failure of a boiler.
There are two types of boiler explosions. One type is a failure of the pressure parts of the steam and water sides. There can be many different causes, such as failure of the safety valve, corrosion of critical parts of the boiler, or low water level. Corrosion along the edges of lap joints was a common cause of early boiler explosions. In steam locomotive boilers, as knowledge was gained by trial and error in early days, the explosive situations and consequent damage due to explosions were inevitable. However, improved design and maintenance markedly reduced the number of boiler explosions by the end of the 19th century. Further improvements continued in the 20th century. On land-based boilers, explosions of the pressure systems happened regularly in stationary steam boilers in the Victorian era, but are now very rare because of the various protections provided, and because of regular inspections compelled by governmental and industry requirements.
The second kind is a fuel/air explosion in the furnace, which would more properly be termed a firebox explosion. Firebox explosions in solid-fuel-fired boilers are rare, but firebox explosions in gas or oil-fired boilers are still a potential hazard.
Principle
Boiler steam explosions
Many shell-type boilers carry a large bath of liquid water which is heated to a higher temperature and pressure than boiling water would be at atmospheric pressure. During normal operation, the liquid water remains in the bottom of the boiler due to gravity, steam bubbles rise through the liquid water and collect at the top for use until saturation pressure is reached, then the boiling stops. If some pressure is released, boiling begins again, and so on.If steam is released normally, say by opening a throttle valve, the bubbling action of the water remains moderate and relatively dry steam can be drawn from the highest point in the vessel.
If steam is released more quickly, the more vigorous boiling action that results can throw a fine spray of droplets up as "wet steam" which can cause damage to piping, engines, turbines and other equipment downstream.
If a large crack or other opening in the boiler vessel allows the internal pressure to drop very suddenly, the heat energy remaining in the water will cause even more of the liquid to flash into steam bubbles, which then rapidly displace the remaining liquid. The potential energy of the escaping steam and water are now transformed into work, just as they would have done in an engine; with enough force to peel back the material around the break, severely distorting the shape of the plate which was formerly held in place by stays, or self-supported by its original cylindrical shape. The rapid release of steam and water can provide a very potent blast, and cause great damage to surrounding property or personnel. A failure of this type qualifies as a boiling liquid expanding vapor explosion.
The rapidly expanding steam bubbles can also perform work by throwing large "slugs" of water inside the boiler in the direction of the opening, and at astonishing velocities. A fast-moving mass of water carries a great deal of kinetic energy, and in collision with the shell of the boiler results in a violent destructive effect. This can greatly enlarge the original rupture, or tear the shell in two.
Many plumbers, firefighters, and steamfitters are aware of this phenomenon, which is called "water hammer". A several-ounce "slug" of water passing through a steam line at high velocity and striking a 90-degree elbow can instantly fracture a fitting that is otherwise capable of handling several times the normal static pressure. It can then be understood that a few hundred, or even a few thousand pounds of water moving at the same velocity inside a boiler shell can easily blow out a tube sheet, collapse a firebox, even toss the entire boiler a surprising distance through reaction as the water exits the boiler, like the recoil of a heavy cannon firing a ball.
Several accounts of the SL-1 experimental reactor accident vividly describe the incredibly powerful effect of water hammer on a pressure vessel:
A steam locomotive operating at would have a temperature of about, and a specific enthalpy of. Since standard pressure saturated water has a specific enthalpy of just, the difference between the two specific enthalpies,, is the total energy expended in the explosion. So in the case of a large locomotive which can hold as much as of water at a high pressure and temperature state, this explosion would have a theoretical energy release equal to about of TNT.
Firebox explosions
In the case of a firebox explosion, these typically occur after a burner flameout. Oil fumes, natural gas, propane, coal, or any other fuel can build up inside the combustion chamber. This is especially of concern when the vessel is hot; the fuels will rapidly volatilize due to the temperature. Once the lower explosive limit is reached, any source of ignition will cause an explosion of the vapors.A fuel explosion within the confines of the firebox may damage the pressurized boiler tubes and interior shell, potentially triggering structural failure, steam or water leakage, and/or a secondary boiler shell failure and steam explosion.
A common form of minor firebox "explosion" is known as "drumming" and can occur with any type of fuel. Instead of the normal "roar" of the fire, a rhythmic series of "thumps" and flashes of fire below the grate and through the firedoor indicate that the combustion of the fuel is proceeding through a rapid series of detonations, caused by an inappropriate air/fuel mixture with regard to the level of draft available. This usually causes no damage in locomotive type boilers, but can cause cracks in masonry boiler settings if allowed to continue.
Grooving
The plates of early locomotive boilers were joined by simple overlapping joints. This practice was satisfactory for the annular joints, running around the boiler, but in longitudinal joints, along the length of the boiler, the overlap of the plates diverted the boiler cross-section from its ideal circular shape. Under pressure the boiler strained to reach, as nearly as possible, the circular cross-section. Because the double-thickness overlap was stronger than the surrounding metal, the repeated bending and release caused by the variations in boiler pressure caused internal cracks, or grooves, along the length of the joint. The cracks offered a starting point for internal corrosion, which could hasten failure. It was eventually found that this internal corrosion could be reduced by using plates of sufficient size so that no joints were situated below the water level. Eventually the simple lap seam was replaced by the single or double butt-strap seams, which do not suffer from this defect.Due to the constant expansion and contraction of the firebox a similar form of "stress corrosion" can take place at the ends of staybolts where they enter the firebox plates, and is accelerated by poor water quality. Often referred to as "necking", this type of corrosion can reduce the strength of the staybolts until they are incapable of supporting the firebox at normal pressure.
Grooving also occurs near the waterline, particularly in boilers that are fed with water that has not been de-aerated or treated with oxygen scavenging agents. All "natural" sources of water contain dissolved air, which is released as a gas when the water is heated. The air collects in a layer near the surface of the water and greatly accelerates corrosion of the boiler plates in that area.
Firebox
The intricate shape of a locomotive firebox, whether made of soft copper or of steel, can only resist the steam pressure on its internal walls if these are supported by stays attached to internal girders and the outer walls. They are liable to fail through fatigue, from corrosion, or from wasting as the heads of the stays exposed to the fire are burned away. If the stays fail the firebox will explode inwards. Regular visual inspection, internally and externally, is employed to prevent this. Even a well-maintained firebox will fail explosively if the water level in the boiler is allowed to fall far enough to leave the top plate of the firebox uncovered. This can occur when crossing the summit of the hill, as the water flows to the front part of the boiler and can expose the firebox crown sheet. The majority of locomotive explosions are firebox explosions caused by such crown sheet uncovering.Causes
There are many causes for boiler explosions such as poor water treatment causing scaling and over heating of the plates, low water level, a stuck safety valve, or even a furnace explosion that in turn, if severe enough, can cause a boiler explosion. Poor operator training resulting in neglect or other mishandling of the boiler has been a frequent cause of explosions since the beginning of the industrial revolution. In the late 19th and early 20th century, the inspection records of various sources in the U.S., UK, and Europe showed that the most frequent cause of boiler explosions was weakening of boilers through simple rusting, by anywhere from two to five times more than all other causes.Before materials science, inspection standards, and quality control caught up with the rapidly growing boiler manufacturing industry, a significant number of boiler explosions were directly traceable to poor design, workmanship, and undetected flaws in poor quality materials. The alarming frequency of boiler failures in the U.S. due to defects in materials and design were attracting the attention of international engineering standards organizations, such as the ASME, which established their first Boiler Testing Code in 1884. The boiler explosion that caused the Grover Shoe Factory disaster in Brockton, Massachusetts, on 10 March 1905, resulted in 58 deaths and 150 injuries, and inspired the state of Massachusetts to publish its first boiler laws in 1908.
Several written sources provide a concise description of the causes of boiler explosions:
And: