# Electromotive force

In electromagnetism and electronics, electromotive force, is the electrical action produced by a non-electrical source. Devices provide an emf by converting other forms of energy into electrical energy, such as batteries or generators. Sometimes an analogy to water pressure is used to describe electromotive force. .
In electromagnetic induction, emf can be defined around a closed loop of conductor as the electromagnetic work that would be done on an electric charge if it travels once around the loop. For a time-varying magnetic flux linking a loop, the electric potentials scalar field is not defined due to a circulating electric vector field, but an emf nevertheless does work that can be measured as a virtual electric potential around the loop.
In the case of a two-terminal device which is modeled as a Thévenin's equivalent circuit, the equivalent emf can be measured as the open-circuit potential difference, or voltage, between the two terminals. This potential difference can drive an electric current if an external circuit is attached to the terminals, in which case the device becomes the voltage source of that circuit.

## Overview

Devices that can provide emf include electrochemical cells, thermoelectric devices, solar cells, photodiodes, electrical generators, transformers and even Van de Graaff generators. In nature, emf is generated when magnetic field fluctuations occur through a surface. For example, the shifting of the Earth's magnetic field during a geomagnetic storm induces currents in an electrical grid as the lines of the magnetic field are shifted about and cut across the conductors.
In a battery, the charge separation that gives rise to a voltage difference between the terminals is accomplished by chemical reactions at the electrodes that convert chemical potential energy into electromagnetic potential energy. A voltaic cell can be thought of as having a "charge pump" of atomic dimensions at each electrode, that is:
In an electrical generator, a time-varying magnetic field inside the generator creates an electric field via electromagnetic induction, which creates a voltage difference between the generator terminals. Charge separation takes place within the generator because electrons flow away from one terminal toward the other, until, in the open-circuit case, an electric field is developed that makes further charge separation impossible. The emf is countered by the electrical voltage due to charge separation. If a load is attached, this voltage can drive a current. The general principle governing the emf in such electrical machines is Faraday's law of induction.

## History

Around 1830, Michael Faraday established that chemical reactions at each of two electrode–electrolyte interfaces provide the "seat of emf" for the voltaic cell. That is, these reactions drive the current and are not an endless source of energy as was initially thought. In the open-circuit case, charge separation continues until the electrical field from the separated charges is sufficient to arrest the reactions. Years earlier, Alessandro Volta, who had measured a contact potential difference at the metal–metal interface of his cells, held the incorrect opinion that contact alone was the origin of the emf.

## Notation and units of measurement

Electromotive force is often denoted by or .
In a device without internal resistance, if an electric charge Q passes through that device, and gains an energy W, the net emf for that device is the energy gained per unit charge, or W/Q. Like other measures of energy per charge, emf uses the SI unit volt, which is equivalent to a joule per coulomb.
Electromotive force in electrostatic units is the statvolt.

## Formal definitions

Inside a source of emf that is open-circuited, the conservative electrostatic field created by separation of charge exactly cancels the forces producing the emf. Thus, the emf has the same value but opposite sign as the integral of the electric field aligned with an internal path between two terminals A and B of a source of emf in open-circuit condition.
Mathematically:
where Ecs is the conservative electrostatic field created by the charge separation associated with the emf, d is an element of the path from terminal A to terminal B, and ‘·’ denotes the vector dot product. This equation applies only to locations A and B that are terminals, and to paths between points A and B with portions outside the source of emf. This equation involves the electrostatic electric field due to charge separation Ecs and does not involve any non-conservative component of electric field due to Faraday's law of induction.
In the case of a closed path in the presence of a varying magnetic field, the integral of the electric field around a closed loop may be nonzero; one common application of the concept of emf, known as "induced emf" is the voltage induced in such a loop. The "induced emf" around a stationary closed path C is:
where E is the entire electric field, conservative and non-conservative, and the integral is around an arbitrary but stationary closed curve C through which there is a varying magnetic field. The electrostatic field does not contribute to the net emf around a circuit because the electrostatic portion of the electric field is conservative.
This definition can be extended to arbitrary sources of emf and moving paths C:
which is a conceptual equation mainly, because the determination of the "effective forces" is difficult.

## In (electrochemical) thermodynamics

When multiplied by an amount of charge dQ the emf ℰ yields a thermodynamic work term ℰdQ that is used in the formalism for the change in Gibbs energy when charge is passed in a battery:
where G is the Gibb's free energy, S is the entropy, V is the system volume, P is its pressure and T is its absolute temperature.
The combination is an example of a conjugate pair of variables. At constant pressure the above relationship produces a Maxwell relation that links the change in open cell voltage with temperature T to the change in entropy S when charge is passed isothermally and isobarically. The latter is closely related to the reaction entropy of the electrochemical reaction that lends the battery its power. This Maxwell relation is:
If a mole of ions goes into solution the charge through the external circuit is:
where n0 is the number of electrons/ion, and F0 is the Faraday constant and the minus sign indicates discharge of the cell. Assuming constant pressure and volume, the thermodynamic properties of the cell are related strictly to the behavior of its emf by:
where ΔH is the enthalpy of reaction. The quantities on the right are all directly measurable. Assuming constant temperature and pressure:
which is used in the derivation of the Nernst equation.

## Voltage difference

An electrical voltage difference is sometimes called an emf. The points below illustrate the more formal usage, in terms of the distinction between emf and the voltage it generates:
1. For a circuit as a whole, such as one containing a resistor in series with a voltaic cell, electrical voltage does not contribute to the overall emf, because the voltage difference on going around a circuit is zero.. The emf is due solely to the chemistry in the battery that causes charge separation, which in turn creates an electrical voltage that drives the current.
2. For a circuit consisting of an electrical generator that drives current through a resistor, the emf is due solely to a time-varying magnetic field within the generator that generates an electrical voltage that in turn drives the current.
3. A transformer coupling two circuits may be considered a source of emf for one of the circuits, just as if it were caused by an electrical generator; this example illustrates the origin of the term "transformer emf".
4. A photodiode or solar cell may be considered as a source of emf, similar to a battery, resulting in an electrical voltage generated by charge separation driven by light rather than chemical reaction.
5. Other devices that produce emf are fuel cells, thermocouples, and thermopiles.
In the case of an open circuit, the electric charge that has been separated by the mechanism generating the emf creates an electric field opposing the separation mechanism. For example, the chemical reaction in a voltaic cell stops when the opposing electric field at each electrode is strong enough to arrest the reactions. A larger opposing field can reverse the reactions in what are called reversible cells.
The electric charge that has been separated creates an electric potential difference that can be measured with a voltmeter between the terminals of the device. The magnitude of the emf for the battery is the value of this 'open circuit' voltage. When the battery is charging or discharging, the emf itself cannot be measured directly using the external voltage because some voltage is lost inside the source.
It can, however, be inferred from a measurement of the current I and voltage difference V, provided that the internal resistance r already has been measured: = V + Ir.

## Generation

### Chemical sources

The question of how batteries generate an emf occupied scientists for most of the 19th century. The "seat of the electromotive force" was eventually determined in 1889 by Walther Nernst to be primarily at the interfaces between the electrodes and the electrolyte.
Atoms in molecules or solids are held together by chemical bonding, which stabilizes the molecule or solid. When molecules or solids of relatively high energy are brought together, a spontaneous chemical reaction can occur that rearranges the bonding and reduces the energy of the system. In batteries, coupled half-reactions, often involving metals and their ions, occur in tandem, with a gain of electrons by one conductive electrode and loss of electrons by another. The spontaneous overall reaction can only occur if electrons move through an external wire between the electrodes. The electrical energy given off is the free energy lost by the chemical reaction system.
As an example, a Daniell cell consists of a zinc anode that is oxidized as it dissolves into a zinc sulfate solution. The dissolving zinc leaving behind its electrons in the electrode according to the oxidation reaction :
The zinc sulfate is the electrolyte in that half cell. It is a solution which contains zinc cations, and sulfate anions with charges that balance to zero.
In the other half cell, the copper cations in a copper sulfate electrolyte move to the copper cathode to which they attach themselves as they adopt electrons from the copper electrode by the reduction reaction:
which leaves a deficit of electrons on the copper cathode. The difference of excess electrons on the anode and deficit of electrons on the cathode creates an electrical potential between the two electrodes. The electrical energy released by this reaction can be attributed mostly due to the 207 kJ weaker bonding of zinc, which has filled 3d- and 4s-orbitals, compared to copper, which has an unfilled orbital available for bonding.
If the cathode and anode are connected by an external conductor, electrons pass through that external circuit, while ions pass through the salt bridge to maintain charge balance until the anode and cathode reach electrical equilibrium of zero volts as chemical equilibrium is reached in the cell. In the process the zinc anode is dissolved while the copper electrode is plated with copper. The so-called "salt bridge" has to close the electrical circuit while preventing the copper ions from moving to the zinc electrode and being reduced there without generating an external current. It is not made of salt but of material able to wick cations and anions into the solutions. The flow of positively charged cations along the "bridge" is equivalent to the same number of negative charges flowing in the opposite direction.
If the light bulb is removed the emf between the electrodes is opposed by the electric field due to the charge separation, and the reactions stop.
For this particular cell chemistry, at 298 K, the emf = 1.0934 V, with a temperature coefficient of d/dT = −4.53×10−4 V/K.

#### Voltaic cells

Volta developed the voltaic cell about 1792, and presented his work March 20, 1800. Volta correctly identified the role of dissimilar electrodes in producing the voltage, but incorrectly dismissed any role for the electrolyte. Volta ordered the metals in a 'tension series', “that is to say in an order such that any one in the list becomes positive when in contact with any one that succeeds, but negative by contact with any one that precedes it.” A typical symbolic convention in a schematic of this circuit would have a long electrode 1 and a short electrode 2, to indicate that electrode 1 dominates. Volta's law about opposing electrode emfs implies that, given ten electrodes, 45 unique combinations of voltaic cells can be created.

#### Typical values

The electromotive force produced by primary and secondary cells is usually of the order of a few volts. The figures quoted below are nominal, because emf varies according to the size of the load and the state of exhaustion of the cell.

### Electromagnetic induction

is the production of a circulating electric field by a time-dependent magnetic field. A time-dependent magnetic field can be produced either by motion of a magnet relative to a circuit, by motion of a circuit relative to another circuit, or by changing the electric current in a fixed circuit. The effect on the circuit itself, of changing the electric current, is known as self-induction; the effect on another circuit is known as mutual induction.
For a given circuit, the electromagnetically induced emf is determined purely by the rate of change of the magnetic flux through the circuit according to Faraday's law of induction.
An emf is induced in a coil or conductor whenever there is change in the flux linkages. Depending on the way in which the changes are brought about, there are two types: When the conductor is moved in a stationary magnetic field to procure a change in the flux linkage, the emf is statically induced. The electromotive force generated by motion is often referred to as motional emf. When the change in flux linkage arises from a change in the magnetic field around the stationary conductor, the emf is dynamically induced. The electromotive force generated by a time-varying magnetic field is often referred to as transformer emf.

### Contact potentials

When solids of two different materials are in contact, thermodynamic equilibrium requires that one of the solids assume a higher electrical potential than the other. This is called the contact potential. Dissimilar metals in contact produce what is known also as a contact electromotive force or Galvani potential. The magnitude of this potential difference is often expressed as a difference in Fermi levels in the two solids when they are at charge neutrality, where the Fermi level describes the energy necessary to remove an electron from the body to some common point. If there is an energy advantage in taking an electron from one body to the other, such a transfer will occur. The transfer causes a charge separation, with one body gaining electrons and the other losing electrons. This charge transfer causes a potential difference between the bodies, which partly cancels the potential originating from the contact, and eventually equilibrium is reached. At thermodynamic equilibrium, the Fermi levels are equal and there is now a built-in electrostatic potential between the bodies.
The original difference in Fermi levels, before contact, is referred to as the emf.
The contact potential cannot drive steady current through a load attached to its terminals because that current would involve a charge transfer. No mechanism exists to continue such transfer and, hence, maintain a current, once equilibrium is attained.
One might inquire why the contact potential does not appear in Kirchhoff's law of voltages as one contribution to the sum of potential drops. The customary answer is that any circuit involves not only a particular diode or junction, but also all the contact potentials due to wiring and so forth around the entire circuit. The sum of all the contact potentials is zero, and so they may be ignored in Kirchhoff's law.

### Solar cell

Operation of a solar cell can be understood from the equivalent circuit at right. Light, of sufficient energy, creates mobile electron–hole pairs in a semiconductor. Charge separation occurs because of a pre-existing electric field associated with the p-n junction in thermal equilibrium. The charge separation between positive holes and negative electrons across a p-n junction yields a forward voltage, the photo voltage, between the illuminated diode terminals, which drives current through any attached load. Photo voltage is sometimes referred to as the photo emf, distinguishing between the effect and the cause.
The current available to the external circuit is limited by internal losses I0=ISH + I
D
:
Losses limit the current available to the external circuit. The light-induced charge separation eventually creates a current ISH through the cell's junction in the direction opposite that the light is driving the current. In addition, the induced voltage tends to forward bias the junction. At high enough levels, this forward bias of the junction will cause a forward current, I
D
in the diode opposite that induced by the light. Consequently, the greatest current is obtained under short-circuit conditions, and is denoted as IL in the equivalent circuit.
Approximately, this same current is obtained for forward voltages up to the point where the diode conduction becomes significant.
The current delivered by the illuminated diode, to the external circuit is:
where I0 is the reverse saturation current. Where the two parameters that depend on the solar cell construction and to some degree upon the voltage itself are m, the ideality factor, and kT/q the thermal voltage. This relation is plotted in the figure using a fixed value m = 2. Under open-circuit conditions, the open-circuit voltage is the voltage at which forward bias of the junction is enough that the forward current completely balances the photocurrent. Solving the above for the voltage V and designating it the open-circuit voltage of the I–V equation as:
which is useful in indicating a logarithmic dependence of Voc upon the light-induced current. Typically, the open-circuit voltage is not more than about 0.5 V.
When driving a load, the photo voltage is variable. As shown in the figure, for a load resistance RL, the cell develops a voltage that is between the short-circuit value V = 0, I = IL and the open-circuit value Voc, I = 0, a value given by Ohm's law V = I RL, where the current I is the difference between the short-circuit current and current due to forward bias of the junction, as indicated by the equivalent circuit.
In contrast to the battery, at current levels delivered to the external circuit near IL, the solar cell acts more like a current generator rather than a voltage generator
The current drawn is nearly fixed over a range of load voltages, to one electron per converted photon. The quantum efficiency, or probability of getting an electron of photocurrent per incident photon, depends not only upon the solar cell itself, but upon the spectrum of the light.